(Quite a) Few questions and anyone local for a quote :-)

widler · Jan 10, 2019

hmtiling said:
It'll be reet mate

I know, its a fad is matting , like that flossing dance kids do, be forgot about soon

Mr Andrew Grogan · Jan 11, 2019

Thanks again for all the replies.

So looks like definitely screed the mat in. Probably not tiling under the kitchen units @3_fall, but probably will be under the island (but not heating under there I guess). Is the screed thick enough that it won't run off the matt and under the kitchen units where there is no insulation? (never had experience with it before so don't know if that is a dumb question).

Was there any recommendations on the tape between insulating boards, needed or not?

Is the WarmFloor Elektra range seen as decent on these forums? Obviously, they seem well priced when comparing to the quotes I've been given from the various tile outlets.

One last thing was what do people do where the tiled area meets a carpet? Given there will be quite a height difference, do they create a slope in the carpeted area to make the drop between rooms smaller, therefore allowing for a tile to carpet door trim to be used or similar?

I have a few additional people coming out to quote for the work (one from here) so I'll hopefully get any further queries answered then

Old Mod · Jan 11, 2019

You shouldn’t fit heating under any permanent floor standing units or sanitary ware, it should be a minimum of 50-60mm away from skirting or heat source, (radiator pipe)
Form some kind of dam at the edges where you want to avoid the slc from running over.
You can use something as simple as a line of sand or even any excess slc powder, or use Silicon to fix a small wooden baton (door stop) around edges, or even thin off cuts of insulation board.
Scrim tape for boards should be alkali free.
You can use slc beneath carpet area by door to provide gentle slope and/or use tile trim to make the transition between tile and carpet.
Carpet and underlay normally totals 20mm + so the difference may not be as bad as you expect.

Dumbo · Jan 11, 2019

As above but find expanding really easy to form a dam just squirt a line on the ground behind kitchen legs.

GoneGuy · Jan 11, 2019

jcrtiling said:
As above but find expanding really easy to form a dam just squirt a line on the ground behind kitchen legs.

Same I find expanding foam quicker and easier

Old Mod · Jan 11, 2019

jcrtiling said:
As above but find expanding really easy to form a dam just squirt a line on the ground behind kitchen legs.

Adey1980 said:
Same I find expanding foam quicker and easier

I prefer something neat and tidy and that doesn’t tear up the board face.

Spare Tool · Jan 11, 2019

I use one inch strips of insulation board stuck with a glue gun, use it also it to set my heights for 6mm of slc over wires..

Dumbo · Jan 11, 2019

3_fall said:
I prefer something neat and tidy and that doesn’t tear up the board face.

You be seen pics of my van . I don't like anything tidy

Dumbo · Jan 11, 2019

Actually glad you worked it out as I never used the word foam

Waluigi · Jan 11, 2019

sharp sand works surprisingly well. Usually better to have a wet bag. Then hoover up when it’s bone dry.

Old Mod · Jan 11, 2019

jcrtiling said:
Actually glad you worked it out as I never used the word foam

I have my moments Jerry.

Boggs · Jan 11, 2019

Like this

Lou · Apr 13, 2024

Don't mind me while I bump up some older but good threads. If you can contribute to the thread, go ahead. But if it's nothing for you then don't reply and it'll soon drop off the What's New page etc.
Worth linking to our new forum structure while I'm doing stuff:-

TF

TF

Old Mod

Dumbo

GoneGuy

Old Mod

Spare Tool

Dumbo

Dumbo

Waluigi

Old Mod

TF

Admin

Subscribe to Tilers Forums

There are similar tiling threads here

Advertisement

Thread starter

Thread Information

Thread Tags

Palace

Kerakoll

Ardex

Mapei

Ultra Tile

BAL

Wedi

Benfer

Tilemaster

Weber

Other (any other brand not listed)

Nicobond

Norcros

Kelmore