Tiling kitchen - painted surface, help!

LJG7777 · May 24, 2020

Hi all,

I know this has been discussed previously but I need help with my specific job...

I want to tile in my kitchen between the wall units and the work surface. It's a new build so I'm sure it's plasterboard painted with magnolia emulsion. My tiles are 100x200mm and will be 5 tiles tall.

What would be the best way to go about this as I'm reading conflicting answers elsewhere? I don't want to fix a tile backing over my current wall for decorative reasons and am worried to sand the paint off as I'm assuming the plasterboard was painted directly and not skimmed over, i.e I don't want to end up sanding the paper underneath. It's too hard to remove and replace the current plasterboard as the units are attached through it and there are around five electrical sockets to deal with.

What would you do based on the above?

Dave · May 24, 2020

Hi.
so they are definitely not skimmed walls ,just drylined and emulsion? , is the paint matt and porous?

LJG7777 · May 24, 2020

Dave said:
Hi.
so they are definitely not skimmed walls ,just drylined and emulsion? , is the paint matt and porous?

Hi, I'm just guessing that they haven't been skimmed however I wouldn't know unless I sanded an area to see. The paint is definitely matt emulsion.

Dave · May 24, 2020

LJG7777 said:
Hi, I'm just guessing that they haven't been skimmed however I wouldn't know unless I sanded an area to see. The paint is definitely matt emulsion.

Score with a knife and see if its paper finish or skimmed

LJG7777 · May 24, 2020

Dave said:
Score with a knife and see if its paper finish or skimmed

Hi, just done that and it's skimmed.

Dave · May 24, 2020

LJG7777 said:
Hi, just done that and it's skimmed.

Ok. Try and see if you can wash the paint off.

LJG7777 · May 24, 2020

Dave said:
Ok. Try and see if you can wash the paint off.

Just used a non scratch scouring pad from the sink, it came off quite easy. See pic - that is a skim showing through isn't it?

Dave · May 24, 2020

LJG7777 said:
Just used a non scratch scouring pad from the sink, it came off quite easy. See pic - that is a skim showing through isn't it?

View attachment 112591

It does yes. Clean it off and leave to dry.
do you intend to use a tubbed adhesive or bagged

LJG7777 · May 24, 2020

Dave said:
It does yes. Clean it off and leave to dry.
do you intend to use a tubbed adhesive or bagged

Tubbed.

Dave · May 25, 2020

LJG7777 said:
Tubbed.

Ok , no need for primer then. Adhere to the drying times before grouting.

LJG7777 · May 25, 2020

Dave said:
Ok , no need for primer then. Adhere to the drying times before grouting.

Ok, thanks for the help!

LJG7777 · Jun 2, 2020

Dave said:
Ok , no need for primer then. Adhere to the drying times before grouting.

Hi. I'm taking the paint off still however I've had to pull off a stainless steel splashback(?) behind the hob. The adhesive from this has pulled off some of the plaster and some of the paper from the plasterboard. I don't want to replace the whole section so would it be ok to prime these bits with PVA or should I cut out the paper down to the plasterboard mortar and then prime?

I could ignore as the majority of the tile will be fixed to the plaster.

Dave · Jun 3, 2020

LJG7777 said:
Hi. I'm taking the paint off still however I've had to pull off a stainless steel splashback(?) behind the hob. The adhesive from this has pulled off some of the plaster and some of the paper from the plasterboard. I don't want to replace the whole section so would it be ok to prime these bits with PVA or should I cut out the paper down to the plasterboard mortar and then prime?

I could ignore as the majority of the tile will be fixed to the plaster.

View attachment 112649

View attachment 112650

don’t prime with pva , sbr or acrylic with suffice and use a patch up plaster and leave to dry

LJG7777 · Jun 3, 2020

Dave said:
don’t prime with pva , sbr or acrylic with suffice and use a patch up plaster and leave to dry

Thanks again!

-

TF

-

TF

-

TF

-

TF

-

TF

-

-

TF

-

Subscribe to Tilers Forums

There are similar tiling threads here

Advertisement

Thread starter

Thread Information

Thread Tags

Palace

Kerakoll

Ardex

Mapei

Ultra Tile

BAL

Wedi

Benfer

Tilemaster /Kelmore

Weber

Other (any other brand not listed)

Nicobond

Norcros