Discuss Debonding of porcelain tiled concrete floor in the Canada Tile Advice area at TilersForums.com.

I need several information about ceramic/porcelain tiles. Hop you could help me out on the following questions.
Most of the contractors are using NPC to install porcelain/ceramic tiles as to reduce the initial cost of the project.
*Debonding is observed only on any size of porcelain tiles installed on concrete floor as this is the only
type of floor is constructed here …..what could be the reason ? will it happen with the ceramic tiles aslo?
* All the incident observed at 4 - 5 years of aged tiled surface. Any special reason ?
* Normally the contractor and consultants here keeps only 2 - 3 mm of tile groves is it ok?
* How can I decide on the width of the grove?
* what could be the expansion of porcelain tile? comparing with the expansion of concrete slab as concrete floor is only our concern here. no more sub floors.
*Any technical evaluation of slab and porcelain tile expansion behavior?
* If adhesive is used how it would fix this issue…..technical explanation plz?
Appreciate if you could help me out for a research purpose study and suggest me to refer any site on the subject matter.
Fahim Ahmedth

 
What size of tiles is it ? 300 mm x 300 mm , 600 mm x 600 mm and 1 m x 1 m

What size area is tiled . ? This is observed in broad area (40 ft x 35 ft) as well as narrow areas (6 ft x 15 ft).

Is there any expansion joints within the tiling field and is there perimeter joints . No, but there are groves of approx 2mm in-between tiles

Do you know what fixing method was used . ? Cement concrete floor ----> Cement/sand tile bed -----> Tiles bonded with cement slurry ( NPC slurry which obtained by mixing with water)

Is the floor heated. ? No. this observed in middle floor as well as in ground floor. Top most floor is a concrete roof top. 2 storied office building, operating with HVAC system
 

Reply to Debonding of porcelain tiled concrete floor in the Canada Tile Advice area at TilersForums.com

Subscribe to Tilers Forums

There are similar tiling threads here

    • Like
Hello, this is my first post here, but I have been doing some reading. I am going to be tiling...
Replies
7
Views
425
I'm planning on tiling my porch, and the tiles and adhesive will take up around 13mm of height...
Replies
2
Views
676
Hi, Need to choose a grout for the above. For the black floor tiles 300x600 am thinking either...
Replies
4
Views
551
hello new here but wished i had found and asked before screed and ufh down but here goes. We...
Replies
12
Views
2K
    • Like
Hi guys. Im a carpenter who has tiled a fair few floors over the years as i fit a lot of...
Replies
13
Views
2K

Advertisement

Thread starter

Joined
Location
Sri Lanka

Thread Information

Title
Debonding of porcelain tiled concrete floor
Prefix
N/A
Forum
Canada Tile Advice
Start date
Last reply date
Replies
2

Which tile adhesive brand did you use most this year?

  • Palace

    Votes: 9 6.1%
  • Kerakoll

    Votes: 14 9.5%
  • Ardex

    Votes: 11 7.4%
  • Mapei

    Votes: 44 29.7%
  • Ultra Tile

    Votes: 17 11.5%
  • BAL

    Votes: 35 23.6%
  • Wedi

    Votes: 3 2.0%
  • Benfer

    Votes: 2 1.4%
  • Tilemaster

    Votes: 21 14.2%
  • Weber

    Votes: 18 12.2%
  • Other (any other brand not listed)

    Votes: 15 10.1%
  • Nicobond

    Votes: 7 4.7%
  • Norcros

    Votes: 3 2.0%
  • Kelmore

    Votes: 4 2.7%
Top