10mm

Recent contents View information Top users
  1. T

    6mm or 10mm cutting wheel ?

    I have a Rubi Pocket 50 Tile Cutter, should I be using the 6 or 10 mm cutting wheel on 300 x 450 x 8 *(6) (B2)* ceramics ? Many thanks
  2. S

    spare 6mm and 10mm wheels for husky

    good morining im looking for spare cutting wheels for my husqvana TC670, i know yorkshire tiling tools used to sell them but unless im blind i cant see them anywhere. im not sure if rubi wheels fit (i doubt it) so any help would be much appreciated :thumbsup:
  3. A

    Laying down 10mm Marmox boards on floor

    hello all, I'm about to lay 10mm marmox insulation boards onto 12mm ply. Do I just stick them down using flexible tile adhesive, or is it also wise to screw them down at 300 centres. If screwing, will the plastic backboard washers be fine with the UFH? regards
    • ap222
    • Thread
    • 10mm backerboard boards down floor laying marmox marmox backerboard tile backerboard usa
    • Replies: 1
    • Forum: British & UK Tiling Forum
  4. C

    10mm Porcelien drill bit

    I need to drill a few 10mm holes in some porcelien floor tiles, I have tried a drill bit from screwfix but it didn't make it through one hole (maybe because I didn't use any water). I have read about the 365 drill bits, anyone recommended something that will do the job that I could also pick up...
  5. D

    Good quality 10mm steel trims suitable for a step?

    Hi, I have some black polished porcelain tiles in my kitchen, there is a small step, so I need a good quality steel trim but I'm struggling to find any online. I've looked at Schluter but they seem to be few and far between in the UK, unless I'm looking in the wrong place? I can find loads of...
  6. M

    Wet saw to cut to 10mm cubes?

    I've never used any mechanical saws before, all my cutting has been with the hammer and hardie up to now. For the my Roman mosaic copies I buy pre cut marble tesserae (tiles), all with a uniform 10mm thickness but an irregular profile. The finished mosaic looks as if all the tesserae have been...
  7. P

    filling 10mm gap

    Hi folks. Fitting a 1600 shower-bath in a 1625 gap, and taking into account the tiles and adhesive, the bath will leave an 18mm gap (give or take). I cant really dot/dab plasterboard to either sidewall to make the gap up, as one has a door, and the other has a window. The rest of the...
  8. aflemi

    wall prep for 10mm porcelain

    Guys, I have just ripped out a bathroom and walls are pretty poor, some skimmed, some plaster basecoat pulled off back to bare brick. I would like to take it all back to brick and 'smooth' over to take porc. What is best way to do this apart from dot'n'dab plasterboard. I need to be tiling...
  9. M

    10mm Slant Ridge Serator Trial.

    OK guys, as some of you know, I took delivery of one of these vicious looking trowels a week ago and have started a job today with a bit of floor tiling on it - so thought I would give it a go:thumbsup: At first it looks like a weapon of war and the plate size is slightly larger than standard...
  10. M

    Where to buy 10mm trims

    Hi all, Can anyone tell me where i could buy 10mm white plastic tile trims. Ive tried topps, b&q, wickes and focus but all they do is 6, 9 and 12.5mm trims. I'm in bristol, so any shops around here would be good, but if anyone has any links for websites that sell them that would be great...
  11. P

    I need to bring up floor level 10mm

    I've been asked to quote a half finished floor. There 'builder' fixed 10m2 60x30 porc to the existing concrete substrate but continued it over 13m2 of parkay flooring with ever-bond. It didn't adhere so they now would like me to finish the job properly. The parkay has been lifted and now...
  12. P

    10mm sq or 20mm crescent?

    Which trowel will leave a higher adhesive bed between a 10mm sq notched and a 20mm half crescent?
  13. U

    400x300mm tile 10mm thick on plastered wall?

    I have purchased some tiles 10mm thick (400x300mm ceramic). The window wall and main bath wall are plaster. the overbath shower wall is plasterboard. Will this be okay or am i taking a chance on the plaster wall? If okay what primer and adhesive and grout could anyone recommend? Any help...
  14. R

    Wall runs out by 10mm over 4metres!

    I'm tiling a kitchen between the units with 100 x 100 ceramic tiles. I have nearly completed one wall which was nice and level, but the second is running out by 10mm. The walls are plastered so I've primed with BAL sbr and I'm using BAL green star ready mix addy. Unfortunately the tiles were...
  15. F

    10mm trowel on wall.

    I'm currently fixing 330x250 ceramic tiles to the wall with a 6mm wall trowell using weber fix plus (max bed 3mm) i'm finding that although i tried to get the wall as level as poss before starting that using these bigger tiles its much harder to get them all level. Can i not just use a 10mm...
  16. Z

    DIY - saw to cut 10mm granite???

    Could anyone offer guidance to a capable DIYer on cutting granite tiles please? I COULD use my B&D 4in Angle grinder with a diamond disc but I really want something to produce absolutely straight cuts to make upstands for the skirting. A bit less dust would be welcome, too! Table wet saws...
    • zygo
    • Thread
    • 10mm bathroom cut diy do it yourself floor granite kitchen saw usa walls and floor
    • Replies: 17
    • Forum: British & UK Tiling Forum
  17. H

    Scoring wheel 6mm or 10mm ?

    I have just bought a rubi cutter which came with a 6mm and a 10mm scoring wheels,Which wheel would be best to use on 150x150 and 100x200 ceramic tiles. Many thanks.
  18. S

    building up to approx 10mm

    can you help a customer ive been to do an estimate for has quarry tiles down (red about 150x150) doesnt want me to take them up, but has had the kitchen extended by1.33mtrs. right the 1.33mtrs is what she has asked me to build up to make it all level.sounds ok but ha, ws going to latex rest of...
  19. Dan

    Price Find: 10mm Square Notched Trowel

    Just thought it woud be good to try and find the cheapest priced tools around by naming a certain tool and using all of our contacts to find the cheapest supplier. 10mm Square Notched Trowel, how much would you pay for this tool from your supplier?

Featured Threads

Advertisement

Back
Top

Click Here to Register for Free / Remove Ad