adhesive

  1. B

    Tile/Adhesive/Plaster Problem

    I started removing the tiles in my bathroom today and the majority of the plaster has come off the wall around the shower/bath area (see picture 1 & 2). No matter how carefully I tried to remove each tile either the tile came away and left the adhesive behind, or it all came off with the...
  2. S

    Drywall adhesive problem

    How do you remove this adhesive from floor tiles
  3. G

    Why is my adhesive dry and crumbling

    I got 100 square metres of tiles laid 18months ago. after 7 months i noticed tiles starting to loosen. now approx 50% have loosened. i lifted a tile last week and the adhesive is dry and crumbling. No real adhesion to floor or tile. Tiles are laid on a concrete floor with no underfloor heating...
  4. G

    Which Mapei adhesive for 600mm porcelain tiles on a concrete floor

    10 minutes ago Add bookmark #1 Which mapei adhesive ( it's convenient for me to buy this brand ) is best suited for laying 600 x 600 porcelain tiles on a dead flat one year old concrete floor. I heard Mapekar rapid set is good ? Wickes sell a mapei fast set PLUS but unsure if it's suitable...
  5. T

    To Remove Old Adhesive & Filler OR Layer Over?

    To Clean Out: Remove Old Glue, Mastic, Filler and Set Back to Studs? OR: to add Glue and Leave what's there in place? The plan is to replace the square tiles with 15"x 30" tiles. I am leaning toward demo, but am I asking for more trouble than one more inch of space and modern insulation is...
  6. F

    Force Drying Adhesive

    hi guys, i was looking at buying a self leveling system from www.simplyufheating.com , i have asked about tiling on the back of the self leveling. is it okay to have the heating on in any fashion or will the heat affect the adhesive or self leveling? Many thanks
  7. W

    Does hardibacker need adhesive on caberdek?

    Hi folks Tiling a bathroom in a new build. Floor is caberdek, solid and flat. Could I just screw the hardi boards down? There's zero movement, or should I still use the adhesive bed? This caberdek looks a bit waxy or has a coating. Cheers
  8. R

    tiles over tiles with thin adhesive suggesetions?

    600 x 600 tiles over 600x600 tiles. Lower tiles solid. WHY is 10 mm of adhesive recommended. I've seen tiles in my house with almost no adhesive underneath and they have been down 40 years. Now I want to put tiles on top of textured tiles (which get dirty too easily) (don't want to remove as...
  9. U

    Cement floor adhesive sealant.

    I'm looking at using STS TG4 cement boards in our bathroom. My local stockist is out of stock of sealant (they offer Illsbruck SP540 rather than STS's own stuff so there must be loads of alternatives? I'm not looking to cut corners, just a suitable alternative - STS only sell theirs in boxes...
  10. W

    Larsen Tile Adhesive and Grout - good or bad?

    I am planning to get 1000x1000 tiles in my kitchen from the following website. In the quote they have also suggested the following tile adhesive and grouting. Larsen Standard Set Flexible Plus Grey Floor & Wall Tile Adhesive S1 Grade...
  11. 1stTimeTiler

    Levelling out Hardie board with adhesive

    Looking for advice on how much adhesive to use. I’ve taken on my first tiling project and found that the chipboard subfloor was affected by water under the washing machine so have cut it out and replaced it with osb and ply (the only way to match the 20mm thickness). However it doesn’t match up...
  12. N

    Larsen Flexible Standard Set Tile Adhesive - to prime or not to prime?

    Hello everyone, I'm about to lay some antique 6"x6"x 0.5" ceramic tiles, all clean and dry, onto a very solid bare (untreated) timber boarded living room floor with no damp or water supply of any sort. Having read that this adhesive sometimes fails to adhere to 1:1 diluted acrylic primer, I feel...
  13. P

    Norcross NX Floor tile adhesive failure

    need eyes in the back of your head. Using Norcros NX standard set floor tile adhesive. After an issue with multipro boards I did some trials with this product. Following tec instructions on the bag, to the letter, after. 4 day cure my tiles pulled off with minimal finger pressure. On primed ext...
  14. Dodger2303

    Best adhesive for very thin gap.

    Hi all I have to replace a handful of quarry tiles on a cement based kitchen floor. I guess a long time ago these tiles were laid directly onto cement (with the cement potentially as the adhesive). I now have thinner tiles so I can relay them onto the concrete only the space between the tile...
  15. G

    Does all types of adhesive stick to SBR?

    I have primed the some of the walls and floor in BAL Bond SBR. The adhesive instructions, (Ultra Tile Fix Proflex), says to prime with their own: "Ultra Tile Fix Pro Primer". So, do all types of adhesive stick to SBR? Thanks
  16. JakubK

    What adhesive would you recommend?

    Hello, I've got to lay 45 X 45cm tiles (1cm thick) on a suspended floor with 22mm chipboard overlaid with 18mm ply (and treated with sbr) What would be best adhesive for the job? Thanks
  17. B

    White adhesive residue stuck to black slate effect tiles.

    I’ve got some white adhesive residue stuck to the surface of black slate effect tiles. Give them a wipe with a damp cloth and the residue is invisible but when it drys it becomes noticeable again. Tried hard bristle brush with boiling water but due to the texture of the tile I just can’t get...
  18. N

    Palace Heat Resist Adhesive

    Does anyone have much experience of working with Palace Heat Resist Adhesive? I'm just about to tile a fireplace with it for a log burner but I've noticed that on the tub it says it will 'take up to 14 days to develop full adhesion and should not be exposed to radiant heat during this time'...
  19. D

    Wrong adhesive for floor tiles (already laid) help!

    DIYer here (and first post!). Done reasonable amount of wall tiling but no floors. New bathroom with concrete base and self leveling compound ontop. I've sadly laid the whole room with our 600 X 400 porcelain tiles using.. deep breath.. mapei showerproof ready mixed tile adhesive which I now...
  20. N

    Which tile backing board, tanking and adhesive for large format tile

    Hi Peeps, about to rip out my bath and put a new one in with a shower. I've done a few bathrooms already but because I'm using 60x60 tiles (28.5kg per m2 Polished ) I just need some advice on what board and adhesive I can use. The tap wall is stud and the side is block. The block is currently...

Featured Threads

Advertisement

Back
Top

Click Here to Register for Free / Remove Ad