backerboard

Hi, Just wondering how i should raise the plywood level so it is flush with the edge of the showertray? Should i use 4mm ply and screw it down? Should i glue the ply down, if so what glue should i use? Should i use some kind of poured / self levelling compound? Thanks, James.

I am looking to fit a wedi tray with wedi backer board and am concerned with the jointing method. Wedi website advises butt sealing the boards and using their tape, bonded with a cement based flexible adhesive. The tape provided does not look waterproof and a cement based adhesive certainly wont...

I am looking to put in two wet shower areas and my plumber has said Wedi are good. looking at buying the the 1400x900 trays and using wedi backer board for walls. I have looked at the wedi kit and see that only water proof tape and cement base flexible adhesive is advised to seal joints etc. I...

I normally use marmox i find it a good product to work with nice and light to use easy to cut and quick to install and have never had a problem with it untill now:mad2: What a let down, I had 50mm boards delivered and i use 50mm loosely! The thickness betwenn the boards varied from 46mm-53mm...

hi peeps,i have to create a 3 peiced bath panel for 3 sides of a steam cabin..all are to be removable and i also need curves for going round to suit the sahpe of it,,do kerdi boards and marmox boards do such a thing as a board you can shape to suit? i have only used the straight wedi boards...

Whats the correct method of fixing 10mm Marmox board to overboarded 18mm Ply?

Hello Has anyone got any experience with Marmox Board CS? Apparently it has a rubber backing which offers enhanced acoustic properties over the standard boards which is what I’m looking for when I replace the acoustic overboard floor in my flat. :thumbsup:

Hi, Flooring a wetroom and planning to use 20mm Marmox ray and boards but I don't have enough room under existing floor for shower waste and pipe so was thinking of layering floor first with 50mm Marmox boards then laying down the Marmox 20mm tray and 20mm boards on top of the 50mm boards. Will...

Help please. I have joined this forum for advise on installing a wedi fundo tray onto moisture resistant chipboard flooring. Adhesive suppliers have told me that there is no adhesive we can use to stick the tray down and we will have to overlay with ply or remove the flooring!! For obvious...

It is way to make product as WEDI board. You have to get this - BASF Group: Plastics - Styrodur: Styrodur® 2500 C and then put something like this broken link removed , inserting into the first coat Fiberglass mesh. It should work.

Anyone got any ideas on the best place to get Wedi board from?

hello all, I'm about to lay 10mm marmox insulation boards onto 12mm ply. Do I just stick them down using flexible tile adhesive, or is it also wise to screw them down at 300 centres. If screwing, will the plastic backboard washers be fine with the UFH? regards

Hi Im after a bit of advice, Im Installing a pre fomed Marmox shower tray but in the instructions it says all thats required due to the tray being waterproof is to apply a membrane tape over the joint of the tray and ply floor then tile as normal. Do you guys have any experience with this and...

OK got marmox shower tray for bathroom and intend to have it level with floor. 1. Plan is to have WEP 15mm ply on floor screwed every 300mm and moisture resistant plaster board on walls. 2. Insert tray and bed into flexible addy and fit drain sealing arund drain with Silicon. 3. Tank both...

What thickness plaster board is required for the bath/shower wall, 9mm or 12mm.does it always have to be primed ? what is the required aqua panel/becker board thickness needed for the same job.

Can anyone tell me best quality tile backerboard to use for wet areas like shower and pool environments? - thanks.