canada

Hello - I'm a homeowner in the process of choosing tiles for a bathroom in a newly built extension. The inner leaf walls are Thermalite 3.6N blocks with a sand and cement render inside. What's the maximum weight of tile that backing could take? I could find lots of information on the maximum...

Merry Chrimbo Tilers! We just bought an arts and craft house built in 1922 and the house has original terracotta tiles in the bathroom which have been painted in parts. I’d like to remove the gloss paint and then protect the tiles from water damage as they are in the bathroom. I’ve read lots of...

Hello we have bought a stone barn that was converted badly to a dwelling in 2003. We’ve got down to the concrete sub floor which we’ve had to heavily patch as we created one room out of 4. Weve laid a radon membrane and a thermal blanket and laid wet underfloor heating. We’ve had a retinol trust...

Hello everyone Im looking for some advice. I currently work for my uncles business tiling for them for around 14yrs but I really want to make the jump and work for myself. I’ve built up some good contacts and do a lot of private work for a few local builders and plumbers. I’m really keen to...

Hello, I need to level the joists. The joists are about 2-3 mm out in places. I would like to level the joists using flexible tile adhesive to the highest point by ruling off using a long feather edge to reference points set in place. The tops of the joists having been pre-cleaned and...

Hello, This is my first post here but I"ve been reading this forum for a while (I've picked up a lot from the "is this a bad tiling job?" threads.). As I'm from Belgium some of the terms will be different but I'll try to be clear. I'm redoing my parents-in-law their bathroom together with my...

Hi All Cheers for the advice on here so far my DIY bathroom build is moving well and the end is in sight. I've used Kerdi board and there are parts of the board that will need painting - so not 100% tile coverage. After some advice on here and from Schluter I'm going to run a layer of tile...

Hi I am want to get my new build kitchen floor, hallway and utility tilled. I am plaining on having Underfloor heating installed in my kitchen an have bought a mat based underfloor heating system with insulation boards(Xp pro insulation board by prowarm) . I got quotations form several tilers...

Hi, I am buying a new build house and the snagging surveyor has raised an issue with some floor levels in a bedroom and 2 en-suite shower rooms, which are out of NHBC tolerance. The main issue is with a tiled floor that is off by 6mm over 2 metres. The build states that it is in tolerance...

Should tiled bathroom floors have ply laid before tiling on a chipboard floor? If so what type of ply and what thickness? Thanks

I had the bathroom refurbed several months ago and about a month or two after the job a large fine crack started to show. It has since got worse and grown. Another hd appeared by the door too. At the time the floor had to be levelled and thick ply put down as a surface. The tiles are from Topps...

I had our bathroom floor tiled several months ago and about a month or two after the job a couple of fine cracks appeared through some tiles. They since got worse. The floor had to be levelled, with thick ply bei used. The tiles are Topps Tiles Checker tiles. Rapid set adhesive was used. I’m...

Hi, Can I please ask for help from an expert? After discovering a leak & some cracked tiles (and that the previous tiler had done a botched job with only putting spots on glue on the tiles) we employed someone from checkatrade to do what we hoped would be a professional job re-tiling our...

Hi, whats the normal method of fixing jacko/wedi board to timber floors. Ive used these boards a fair bit before but never on floors so im unsure on what way round to do it... Do you set them with rapid set then add the fixings while the adhesives still wet or wait until its set and then add...

Hello guys, I'm new to the forum :) So you know my skill level.., I'm currently training at a Construction school in wall & floor tiling, due to qualify in June 2021. Next month, I'm tiling my brothers kitchen and he wants a steel trim fitting. I will be using a hacksaw and mitre block to...

Hi, I've put down quite a bit of tile over the years but always worked with backerboard. I'm renovating a house in Florida (first one in Florida) that was built in 1996. It's concrete slab foundation and the tile was laid directly on the slab with what appears to be basic thinset. When I was...

Hi all, new to the forum and looking for a bit of advice. I’ve stripped out an old bathroom and I’m getting the walls prepared for our tiler to come in. there is one section that I don’t want to remove if I don’t have too and I’m hoping the tiler would be able to tile over? So my question is...

Hi guys, Just a quick question regarding packing out the difference between the tile height and the plasterboard. I've stuck a few mirrors on before but they've always been on a solid wall rather than plastboard, and these tiles are thicker than anything ive used in the past, being 10mm...

Hello, I can cope with cosmetic problems but the tiler is 3/4 way through and I noticed he is using random blobs of cement not spreading it over the tile. There are big gaps between the tiles and the edges have no adhesive. It is behind sink and loo and around the bath and a new shower at one...

Can I ask advice please; I have MS and the worry is making me ill. The tiles are all chipped. The tiler says it is the tiles they need specialise equipment to cut so we have to put up with chips all round window- at first he was going to hide with trim but it looked wrong. See pics. he has...