hole

  1. M

    Please advise I’ve managed to disconnect my pipe under the kitchen sink plug hole

    Can I just get some advice please? I was a bit over enthusiastic cleaning my kitchen sink and I’ve managed to disconnect the pipe part under the plug hole!! Continue reading...
  2. M

    Please advise I’ve managed to disconnect my pipe under the kitchen sink plug hole

    Can I just get some advice please? I was a bit over enthusiastic cleaning my kitchen sink and I’ve managed to disconnect the pipe part under the plug hole!! Continue reading...
  3. Chris_32

    Hole saw bits Which is best?

    What are people’s opinions on different brands of hole saw, specifically the M14 ones that can go on the grinder. I have started using Marcrist dry cut ones and they’re brilliant but expensive. Just wondered if there are any others out there that last as long and cut as well for a slightly...
  4. Lou

    Should I drill a hole above these switches? Electrical Advice

    Should I drill a hole above these switches? Discussion ThreadShould I drill a hole above these switches? Electrical Advice Just about to install the end of a curtain rail but am thinking twice… Would be above a light switch and a few outlets. Is there a safe way to do this? How do I post a...
  5. S

    Repairing large (130mm) hole in tile

    I had some work done leaving an approximately 130mm diameter hole in the floor & tile where pipes previously came through. Wondering if it would be best to replace the entire tile or just patch it with a piece of tile? I know normally it would be replace the entire tile as this would...
  6. Y

    Filling hole in floor before tiling

    Hi All I need advise on how I go about filling hole in picture before I can tile the tray with mosaic tiles?
  7. G

    Can you recommend good hole saws( drill bits)

    What's your tiling question? Pictures can be added.can anyone recommend good Diamond hole saw (drill bits) that go through porcelain and lasts. Thanks Gerwyn (GD TILING)
  8. E

    Hole or air bubble within porcelain?

    Hi can anyone help me understand what has happened to this tile? It is porcelain and dropping a lightweight plastic chair (leg shown) has caused this hole. It looks like there was an air bubble within the tile. Is that a thing? I can’t find anything like this on the web. The tiles are also...
  9. E

    hole in porcelin tile

    hi all ive put the 2 feed pipes in the wall for the shower and am ready to tile the wall using pocelin tiles and so need to drill the holes in the tiles what type of hole cutter would i need to use? thanks george
  10. P

    4 1/4" hole in 2x10 floor joists

    i noticed when removing some subfloor that the builders placed a 4 1/4" hole for a toilet waste pipe in 2 floor joists on the second floor. the joists are 2x10 and the span is 27'. the bottom of the hole is 1" from the bottom of the joist. i have been asked to tile the floor of this room with...
  11. A

    Small Hole in Grout

    Hi all, I have had this small hole in the grout of my bathroom for about 6 months, I am ashamed to admit I am completely ignorant when it comes to any form of tilling or DIY for that matter. 😳 Is a hole this size likely to cause an issue? This tile is right under the shower, I am a bit...
  12. A

    Tile hole drill bit set. Which one

    I'm looking information on a drill bit hole set and a decent 4 inch blade that'll cut all tiles. I used to buy the 365 hole set however I can't seem to find online the set I used to purchase. Infact I can't find much of that brand anywhere. Maybe they've stopped making them. It's been a long...
  13. Micky karma

    Hole cutter

    Hi Folks, Could somebody please point me in the right direction as to what they consider the best hole cutters/ drill bits are for porcelain tiles please. I seem to be throwing good money to bad on what I’m buying !! 😡
  14. Dan

    Cutting a hole in a tile with a grinder

    Not seen it done this way before.
  15. R

    Hole cutters cheap supplier

    Whats the go 2 place for porcelain cutting cheap hole cutters and whats the top make currently so i can build up a collection. I use to richon years ago but not sure if theirs a better place thanks.
  16. M

    Tiling over hole in plasterboard and around taps

    I have had new taps and plumbing installed on an existing tiled wall for a freestanding bath. The plumber removed 2 wall tiles to install tapware and water outlets. This has left a hole in the plasterboard where the 2 tiles were. Can anyone advise the best way to replace the 2 tiles, given...
  17. acaciaguy

    Recommend me a new tile hole saw set

    its time to get a new set. Any suggestions?
  18. Lakey

    Hole Cutter Recommendations

    Chaps Looking to invest in a new set of hole cutters. I previously had the Marcrist Wet drill kit which has served me well. I'm after preferably a dry kit to include 6mm, 8mm, 32mm & 40mm as well as a hole size enlarger bit. Anything else i'm missing? Cheers
  19. R

    What filler to fix hole in plaster board?

    Hi all, I have a wall that has two layers of plaster board, the wall is in good condition apart from one thing, there is a hole about 4 inches wide by 3 inches high and about 15mm deep, i really don't want to rip down a whole wall due to one hole, can it be filled ready for the wall to be...
  20. Pritch

    Advice how to cut out a square hole.

    Hi Could anyone give some advice on how to cut out this flush plate that falls in the middle of the tile? Thanks

Advertisement

Back