metal

  1. Lou

    WIFI devices in a metal consumer unit. Electrical Advice

    WIFI devices in a metal consumer unit. Discussion ThreadWIFI devices in a metal consumer unit. Electrical Advice Good morning. I intend to replace my oil boiler with electric and a qualified electrician will be doing the job. I see there are lots of din rail mounted WIFI devices such as...
  2. E

    Original Y4REK white Tile Remover Puller Tool for Metal Suspended Ceilings Tile

    Made from stainless steel for the best quality. Continue reading...
  3. E

    Metal Ceiling Tile REMOVER Tool

    High Grade Stainless Steel Die cut by press. Wooden handle made and fitted by hands. Continue reading...
  4. E

    Metal Ceiling Tile Remover Puller Tool- Stainless Steel Wood Handle

    Two Suspended ceiling metal tile puller’s/removers, with stainless steel blades and wooden handles.One is new and unused and the other used on one job and in good condition. Continue reading...
  5. E

    Metal Ceiling Tile Remover Puller Tool

    · Service: 24-48 Hour. Continue reading...
  6. E

    10" Contour Gauge Duplicator Profile Ruler Tiling Laminate Tool with Metal Lock

    (PREMIUM BUILD QUALITY) This sturdy contour profile gauge has been engineered to the very highest standards. Providing high strength and long-lasting durability with total rustproof protection. It will make a perfect gift for dad or the budding DIYer. Continue reading...
  7. Lou

    Metal conduit Electrical Advice

    Metal conduit Discussion ThreadMetal conduit Electrical Advice Does metal conduit need earthing , and if so what size ? I’ve pulled twin and earth double insulated cable through old metal pipes, previously used for singles, the circuit is on a RCD. Metal conduit for the original thread on...
  8. M

    Texture metal lined pipe? Discussion Thread

    Texture metal lined pipe? Discussion Thread Hi guys Any of you use the above pipe at all? If so, do you use only tectite fittings or any other manufacturers? Texture metal lined pipe? for the original thread on Plumbers Forums
  9. N

    Help Needed: Fixing My Damaged Tub with Devcon Metal Patch & Fill Discussion Thread

    Help Needed: Fixing My Damaged Tub with Devcon Metal Patch & Fill Discussion Thread Hey everyone, I have a pretty messed up tub that I need to fix, and I'm hoping to get some advice on how to do it. I've attached pictures of the damage and the Devcon Metal Patch & Fill (Charcoal Gray) that I...
  10. Lou

    Supply Isolator required to be metal on TT Electrical Advice

    Supply Isolator required to be metal on TT Discussion ThreadSupply Isolator required to be metal on TT Electrical Advice Does the Supply Isolator require to be metal on TT, is so metal could become live because before RCD Supply Isolator required to be metal on TT for the original thread on...
  11. K

    Crazy gap between shower metal frame and tiled wall

    Hello and thanks for your time. When the shower metal frame (that will hold the glass wall) is placed plumb along the tiled wall, you can see that the tiled wall is uneven. The top and bottom touches the tile wall but in the middle there is a huge 2cm gap between the metal and wall. Basically...
  12. B

    How do I fill this gap between marble tile and metal window frame?

    Hello everyone. My building had bricking work done on the outside and it seems in the process they've yanked the shower window away from where it was seated before. Creating this gap between the tile and exterior frame. How do I fill this gap? Should I use grout or something else? Thank you!
  13. A

    How to trim, metal tiling trim after it’s been installed

    Hi, new to forum and first post, after some advice. Recently had the chamber of my fireplace tiled and the front two side edges of the chamber had metal trim added to finish it off. The tiles were 9mm I believe and to allow for the adhesive, 12.5mm trim was used. Unfortunately this has meant...
  14. R

    Wet saw plastic or metal construction?

    Hi, I am looking at wet saws and only a DIY here but got a few odd shapes to cut. What would people recommend between the cheap plastic type wet cutters like the Mac Allister or a metal based one? Such as Performance Power PTC450E 450W Brushless Electric Tile Cutter 230-240V -...
  15. Sophietilingbeginner

    Precision cutting metal tile trim

    Hi, we have bought the nickel finish box shape stainless steel trim (link below) we have tried to cut it with an angle grinder and a saw, the heat of the angle grinder is ruining the finish and the saw isn’t giving us the clean finish we are looking for, we need to cut 45 degree angles, is this...
  16. T

    Metal trim jutting out at corner, creating sharp point.

    Coming to the end of a bathroom fit, just inspected some trim fitted at a corner yesterday and where 2 trims meet it juts out 5mm creating a sharp point. Doesn't seem correct to me. What is the solution when I speak to them next week?
  17. A

    Best black metal tile trims

    Hopefully a quick one. Can anyone advise the best 12mm black metal tile trims. I. E. The hardest wearing as I never intent on changing the tiles. Are the pvd coated ones any good? Black porcelain tiles.
  18. BinaBold

    I'm Looking For This Tile Allen + Roth metal elements backsplash tile

    purchased from Lowes. item number 526253
  19. M

    brushed metal trims for sale ( bargain )

    BRUSHED METAL TRIMS FOR BARGAIN PRICES. 100 LENGTHS 8MM BRUSHED = 500.00 POUNDS 100LENGTHS 10MM BRUSHED = 500.00 POUNDS MORE IN STOCK CAN DO 50 LENGTHS PACK JUST ASK? WE ALSO HAVE 3 AND HALF ROLLS OF ACOUSTIC RUBBER MATTING ( 4.5MM THICK ) JOB LOT = 200.00 POUNDS
  20. M

    Plastic and metal edging in kitchen

    I'm tiling my kitchen with white marble tiles, I wanted to have the top that meets the plasterered walls have metal edging and any corners that meet with other tiles be done with white plastic edging. Will this look normal combining both and is it normal practice?

Advertisement

Back