resin

Afternoon all, As I have been let down on a 2 week job the lovely wife suggested I get on and refit the ensuite, a job that was in the pipeline that I had managed to put off. All has been stripped back to plaster on 3 walls and plasterboard replaced with Hardie. This ensuite is in an extension...

The Tile Association has published its eagerly anticipated technical document, with the aim of providing advice for all parties involved in the use of resin agglomerated tiles. Click here for the full article.. RSS feed from For tiles, tilers, tiling and the tiles industry: The Tile Association.

Hi, I have a problem with very slight movement in marbe floor ties laid 2 years ago, the issue seems to be with the adhesive and methd ( dod and dab) of laying . After lots of Q&As, i came to the understanding that the only fix would be to lift and relay. However I got a marble tile restoration...

Hi Guy/Gals. I looking for a primer so i can laytex on to a resin floor. I've been told by TA rep that i can use a primer by mapei called primer p4 but i cant find it in the product range. Its a type of primer that leave the floor gritty to allow the laytex to stick. Must be a flexible type...

Hello folks, Next week if tiles arrive I have a bathroom floor and shower to tile. The tray is is in place in the middle of a wall on floor. It's a white shiny resin formed tray flush with floor and pre formed drops to the drain. I have to envelope the tray with the floor tiles. Has any of...

Guys and Gals, This is something I have not encountered before as far as restoration is concerned, basically, the walked on areas seem to have lost the wear layer, and the light traffic areas still have the gloss polished finish. (On some of the part worn tiles, the wear layer has a jagged...

Hi all I was wondering if two part resin can be used instead of grout.This way I could match the colour much better giving for example,a stone tiled shower the appearance of solid slabs of stone.Is this possible?anyone done this before? any advice welcome Thanks.

Hi Guys (1st time post) I am about to embark on a wet room project on our house, The room is 1.8m x 1.6m, we are planning on using some sort of resin shower tray possibly 1200mm x 1200mm Marmox showerstone or Tuff 2, building up the surrounding floor with plywood to get the floor flush with...

Hi Guys First post so please be gentle I have a 1500x800 stone resin shower tray to fit, it's going on 18mm wbp ply and i was going to bed it in on sinlge part flexy my question is how thick should the bed be? The ribs beneath the tray are about 7-8mm off the ply so was thinking about 12mm...

In a related thread I mentioned a job I'd done, well here are some photos Prepped and primed UFH laid Green inner first Grey outer an skirting I rang them up today too to see if they had had any problems - and all is well :thumbsup:

Does anyone know where to get a resin that will repair stone tiles?(corner broke off).I have searched all local tile shops and found nothing!And how would one go about matching the colour All help appreciated.

All, I have created a timber 4 X 2 plinth to put my quadrant (1000 x 800) stone resin shower tray on. I have 18mm WBP ply on the top. The manufacturer's instructions say to bed the tray into a sand and cement mix. I have a couple of questions regarding the best way to install this tray...

Well most of my plans for a wetroom seem to curry disfavour from what I've read on this site. I was hoping to angle 4 plywood triangular sections towards a central waste. Obviously means taking up to an inch off existing joists at the centre of the room. As the joist depths were 10" I thought...

Hey guys, Can anyone suggest where to get some trav filler in Central Scotland idealy East coast. I am going to repair some trav where the filler has began to crack. I know some guys use expoxy grout but, I am looking to use the resin filler. It would be handy to find a local retailer as...

Has anyone had a problem that i have encountered recently where a limestone floor was laid using a flexible thickbed white adhesive. Adhesive was spead over back of tiles before solid bedding stone in extra adhesive and there was full coverage underneath. A number of months later the floor...

Hi I've done a lot of searching around but I can't quite find the information I'm after on the internet. I'm after some advice on injection resins and fixing studs. I'll shortly be fitting a heavy half pedestal porcelain hand basin in my bathroom. I've had to create a 'false wall' to allow for...

Going to fit a stone resin slimline shower tray (1200x900x40mm) to the bottom end of a bathroom to turn it into a shower room. Never done this before so looking for advice - I presume I will have to make an opening in the floor (Chipboard by the way) to take the waste trap and give and connect...

Hi to all, Been sourcing some travertine tiles that have clear resin in the holes then laquer over the top instead of the normal white fill, looks really good. only Topps seem to have them in their premium stone range cant find them anywhere else... comes to about £1400 from topps so...

I would like to make a custom tile by milling out a pattern then filling it back in .....Ideally with some kind of blue resin ...any ideas ???

This may sound like a really stupid question but i've been asked to tile a kitchen and utility floor with porcelain large format tile which i'm fine with. however there's a black sticky resin thats been left on the floor. I want to know if i can i lay the tiles on this or will i need to lift it...