Hi,
Currently in the middle of renovating an old property, dug up old quarry's and self levelled! Still out by 10/15mm in spots so looking for a waterproof thick bed adhesive. Needs to be water resistant due to do DPM, have used ardex NA for Self levelling as moisture resistant.
Anyone have...
Sam2494
Thread
adhesive
floor
resistant
thick
tile adhesive
water
http://www.homebase.co.uk/en/homebaseuk/new-luna-beige-wall--floor-tiles---30-x-60cm-306547
they will be going on a mixture of walls. 1 x skimmed plasterboard, 1 x concrete render, 1 x plastered render and 1 x 6mm hardibacker screwed onto 18mm marine ply.
NB: bath/shower area tanked with...
gooty
Thread
adhesive
porcelain
porcelain tile
primer
thick
tile adhesive
what
These tiles have been mention by RayTT at his showroom in south London and i doubt many have fixed these.
These are made by GRESPANIA Cerámica inteligente | Coverlam | Porcelánico Laminado and the tile is Cerezo, a customer has perhaps choosing these for a large floor and at that thickness...
I have a floor that is uneven in places and want some advice on best approach to finish it. Its a bathroom and the tiles are 550x550mm and floor is uneven all over. The toilet is on external wall and both sides of the toilet to both walls is about 1m. It is a slope of near an inch into each...
The 'web' seems to recommend 4mm notched trowel for mosaics (porcelain)
Is this correct and if so is the notch smaller than you would use on the floor to stop adhesive coming through the gaps?
Many thanks for your help
peterparker
Thread
10mm
aus
best
mosaic
mosaic tiling
mosaics
thick
tiling trowel
trowel
usa
Hi, I have a job to look at were the customer has purchased 1mm thick 200 x 75mm glass brick effect tiles from walls and floors. Just wondering what the adhesive to use with these tiles as there glass and 1mm thin? she also want's a silver star speckled like grout. :smilewinkgrin:
I've just installed my shower tray and tanked the walls (one side hardiebacker, one skimmed plaster).
Where my existing brick wall is out of level I have a gap of about 10mm at the worst point where the shower tray abuts the wall.
I have flooded the wall and gap with Silicon and then tanked...
I have a job starting very soon and we are honing all exposed edges rather than mitre of using trim.
what do you charge for this work on site per lin mt.
material is crema grey light honed 600x 600x 20mm.
Hello all. Hope all ok.
Last Friday I went to look on job. And it is a 10 mm limestone 30 sq m on a concret . The problem is part of the floor been done by customer (woman) not this 30 sq m And when she did the floor she did not realised that floor was not in level and end up with 10-15 mm of...
i have a job that requires laying 800 x 600 tiles.
weber thick bed adhesive is about the same price as a decent SLC, so why not just use thick bed adhesive and tile the floor level as you go rather than use SLC to level a floor?
it is quicker (i can start tiling today), requires less priming...
Dear all,
First time and hoping for help! I have a AKW tuff form / level best tray installed (by builder) to create a level access shower and, because of various issues the tray is now at least 20mm below the level of the finished floor porcelain tiles around it. I plan to lay 10mm x 50mm x...
rookie
Thread
adhesive
aus
best
boards
level
thick
tile adhesive
tray
usa
I am going to lay some Hardibacker board tomorrow, but I have a question. How thick will the bed of adhesive be if I use a 6mm square notched trowel and how thick if I use an 8mm square notch? The instructions recommend a 6mm but I only have an 8mm, should I just use it or buy another? That was...
Anyone know of a levelling system the does the above? Also any considerations when using tiles of this thickness? It's a composite stone going around a swimming pool but 1200x600 and i think lifting up to pack is gonna be a struggle and also concerned that a tile of that size will have so much...
JLM Tiling
Thread
aus
levelling
levelling system
system
thick
tile
tiles
usa
Hi guys! Im trying to finish UFH in my toilet, but met two problems.
Obviously I cannot shortened loose wire, thats clear. But what about loose wire beggining? Its thick and I have probably at least 1.5m longer wire than it suppouse to be( 1.5m from the gang).
The same problem is with the...
Hi,
I am tiling a shower cubicle and am a bit of a novice - certainly with glass tiles as I have not had to use these before!
A few questions if I may.........
Am I correct in thinking that it is best to tile the boards in their entirety bfore fitting the cubicle or is it best to fit the...
Scholester
Thread
best
best way
board
cement
cement board
fix
glass
glass tiles
please
thick
tile
tiles
usa
hi all
been to look at a job and ive been booked in, 20m conservatory with undertile heating.
now they have had their heads turned by the marble work top fitter. he has said that in hampstead heath and other posh london places people are having slabs of marble cut into 1500x1000mm tiles and...