Plumbing Advice

Underfloor heat pipe specification and pipe centres and radius bends. Discussion Thread

In my attempt to future proof my underfloor heating design to maximise the heat output at the lowest possible mean water temperature, I am planning pipe 16mm dia pipe centres at 133mm governed by the nature of the installation (3 pipes per space between floor supports at 400 mm ctrs. - Serpentine layout.
I would welcome any advice on the best possible pipe spec or brand for this approach so...

 

Obstructed pipe q can I Reposition toilet pipe Discussion Thread

Hi
I have a problem about waste pipe positioned over the front door
A bathroom was turned into a 3rd bedroom. The toilet and sink was moved to a storage room just behind the 3rd bedroom. The waste pipes were put under the floor. Everything works fine but the customer wants the waste pipe to be lifted above the decorative plaster .
I’ve been advised that is not possible as the waste needs to pass down to the soil pipe...

 

Saying hello to all on plumbers forum Discussion Thread

Hi Everyone, I'm a DIYer that's do e basic plumbing (replaced a couple of bathrooms) but nothing complicated. Looking to get advice on a pump for domestic gravity fed hot water in the house but will create separate post later.

Saying hello to all on plumbers forum for the original thread on Plumbers Forums

 

Damped oil pump pressure gauge recommendation Discussion Thread

I have 2 oil pump pressure gauges, a Nu-Way un-damped one that I have had for well over 30 yrs and no name brand that the glycerine is going white and leaking. Can anyone recommend a good damped one. Ta

Damped oil pump pressure gauge recommendation for the original thread on Plumbers Forums

 

Can I move toilet waste pipe above decorative moulding outside front door Discussion Thread

Hi
I have a problem about waste pipe positioned over the front door
A bathroom was turned into a 3rd bedroom. The toilet and sink was moved to a storage room just behind the 3rd bedroom. The waste pipes were put under the floor. Everything works fine but the customer wants the waste pipe to be lifted above the decorative...

 

Replacement Diverter valve for obsolete tap Discussion Thread

Hi,
I have a Bristan Matrix Bath Shower Mixer Tap, the diverter valve has been temperamental for some time and has finally failed with a split rubber washer. The tap is obsolete and spares are no longer available.
(I have contacted Bristan.)
The bath is built in and access to the tap is not possible without a lot of dismantling.

Does anyone recognise the washer, (dimensions are approximately 25mm dia by 10mm thick...

 

Great to be with the plumbing gurus here. you're awesome Discussion Thread

Hi guys. Feels good to be here. Can’t wait to learn and share my experience

Great to be with the plumbing gurus here. you're awesome for the original thread on Plumbers Forums

 

Does anyone have any idea how to purchase FM MATTSSON parts in the uk? Discussion Thread

Hi all. I work doing maintenance at a student accomodation village and we have a large number of mixer showers with valves by FM MATTSSON. They are a swedish company.
I am particularly looking for spares for the on/off valve.

Does anyone have any idea how to purchase FM MATTSSON parts in the uk? for the original thread on Plumbers Forums

 

Changing from system to combi boiler with under floor pipework. Discussion Thread

Wondering should i change a system boiler with a combi if I have underfloor pipes in a single storey 2 bed 90s bungalow There are only 9 bungalows in the close and I was told 2 of these had leaks in floor when they changed to a combi by a neighbor. He said as he was an engineer he would not advise the change as it was something to do with the different pressures the boilers operate on. What are the...

 

Qualified Trainee / Improver Seeks Start Discussion Thread

Hi - I am looking to return back to the industry. I completed a three year adult apprenticeship having qualified with the City & Guilds Level 2 and the NVQ Level 2 in Plumbing & Heating. I have three years experience. I am based in Carshalton in Surrey / Greater London. I want to get back into the trade but finding positions in proving to be difficult. Due to covid bereavement i left the firm I was with in South Kent and...

 

Qualified Trainee / Improver Seeks Start Discussion Thread

Hi - I am looking to return back to the industry. I completed a three year adult apprenticeship having qualified with the City & Guilds Level 2 and the NVQ Level 2 in Plumbing & Heating. I have three years experience. I am based in Carshalton in Surrey / Greater London. I want to get back into the trade but finding positions is proving to be difficult. Due to covid bereavement i left the firm I was with in South East Kent and...

 

First post that is required to maintain account Discussion Thread

Hi
Newbie here just wanting to learn from everyone here
Thanks

First post that is required to maintain account for the original thread on Plumbers Forums

 

Alternative to Everbuild Plumbers Gold? Discussion Thread

Can anyone recommend an alternative to Everbuild Plumbers Gold? I have always used this with great success, but the latest tube doesn't seem to work as well as previous tubes. Have the changed the formula when they moved from black tube to a grey tube?

Alternative to Everbuild Plumbers Gold? for the original thread on Plumbers Forums

 

Heat Exchanger with AGA and heat pump Discussion Thread

Hi All I have a client asking whether they can still use the AGA to heat rads once the air source heat pump is in. I think it is possible using a heat exchanger so the low pressure AGA and high pressure heat pump systems don't connect. I've seen it done on biomass systems but wonder what the implications are with heat pump legislation

Heat Exchanger with AGA and heat pump for the original thread on Plumbers Forums

 

Home DIYer posting to retain account. Discussion Thread

Drayton equipment fitted to CH system & very old Aqualisa Aguavalve 200 shower so have used this site for advice: very useful.

Home DIYer posting to retain account. for the original thread on Plumbers Forums

 

Home Diyer posting for account to remain Discussion Thread

Quick hello,
Need to keep my account.

Home Diyer posting for account to remain for the original thread on Plumbers Forums

 

Mains Water Closet direct Flush valves still a rarity in UK? Discussion Thread

Just was at a caravan site in Lake District recently, which had some very interesting Delabie electronic tap and shower fittings, also direct WC flush valves which worked extremely well.
Always wondered why these valves didn’t seem to catch on in UK when very many other countries never use cisterns.
A quick look in the Delabie specs sheet reveals their valves require a 20mm bore feed capable of around a...

 

Anyone done the heat geeks online courses? Discussion Thread

Has anyone done the online heat geeks training? I believe you get a BPEC certificate when completed. It's a self study course. Thanks

Anyone done the heat geeks online courses? for the original thread on Plumbers Forums

 

Best way to connect 10mm plastic pipe to 8mm micro bore Discussion Thread

Hi all fitting new radiators and need to connect to 8mm micro bore copper pipe under floorboards, (full rework of pipes not an option) would 15mm plastic pipe be okay or just go up to 10mm plastic pipe ? Also best way to connect , compression or push fit ? Using inserts off course , additionally if I drained system down through current radiator valves would there still be a lot of residual water ,combi boiler...

 

What are the best heating flushing systems Discussion Thread

Any advice on selecting the best central heating flushing system would be most greatful

What are the best heating flushing systems for the original thread on Plumbers Forums