coverage

  1. S

    Filling and Sealing Joint between Tile Backer and Ceiling

    I’m just about to install 12.5mm Hardiebacker boards in my 3-wall en suite shower and I’m just wonder how I should fill and seal the joints with the existing ceiling (believe it is just plasterboard and painted). What should I use for filler? Tile adhesive and then tape the joints as normal...
  2. Anthony Wills

    Your thoughts on coverage?

    Hi I layed 4 tiles for a customer in a front door entrance. The customer then wanted me to rip up the carpet and tile the whole hallway in the same tiles. This meant taking up the tiles I layed. They came up with no difficulty and saw there was pretty good coverage in under most of the tiles imo...
  3. J

    The correct method of sealing sliding shower doors

    Hi all. I've seen a fair share of very dodgy siliconing around the frames of shower doors. The installation instructions for my shower door state that you should not seal the inside of the frames, only the outside. This make sense to me. But in reality, what does it mean? Do you dry fit the...
  4. J

    Best method of sealing porous tiles

    So I had to seal some slate the other week which I did with a paint brush. Just wondered if there was a better method? (I used the Tile Rite stone sealer) and applied 2 coats and then tested with a whiteboard marker on a spare off cut.
  5. W

    sealing tiles in our bathroom

    Hi Could anyone recommend the best sealant to seal these tiles please? We’ve finally got our shower up and running but water is getting through some of the grout joints on our tiles, so I’m hoping i can give them a seal? Any advice or suggestions I would be greatly thankful for Cheers
  6. T

    Encaustic tile sealing and hairline cracking

    Hi, Looking for advice please. 2 problems! We have just had encaustic tiles laid in our bathroom including wetroom style walk in shower. They were laid over a new floor (extended bathroom) which then had a layer of hardiebacker cement board on top screwed down all over it. The tiles have been...
  7. P

    Black Limestone – Sealing before jointing

    Hello From this forum I understand that I need to seal before jointing and understand that I need a combined impregnator and sealer. My intention is to colour enhance the stone to get it back to black. I have come down to a choice between 2 products: Romex colour enhancing sealer Miracle 511...
  8. P

    Bath trim and resealing advice please .

    Hi folks .Nees some advice .I had a bit of water cone through the kitchen ceiling the other night .Realised the trim around bath needs replaced but its a quarter round trim and seems to go up behind the bottom tiles.Is there a way to reseal without removing the bottom tiles .
  9. Stevev

    Spanish tiles.... Need sealing before grouting?

    These tiles look as though the design has been printed on. There's no glaze like a metro tile. Will I need to seal before grouting? Thanks
  10. T

    No limits 'kerakoll' coverage

    Evening, Has anyone used this? Kerakoll say that there 25kg bag will do 7.5 M2 on a 10mm trowel. Just wondered if anyone has had the opportunity to put this to the test.
  11. M

    Sealing - Jura Limestone

    Im laying 600x400x15 Jura Beige honed tiles on my kitchen floor, and have received conflicting advice! I bought LTP Mattstone with the tiles, along with the recommended adhesive and grout. A builder friend advised to seal the front and back before installation which I’ve been diligently doing...
  12. R

    Cleaning flamed granite and sealing, flamed granite(if required)

    Good day everyone! I had a granite company do a supply and install of flamed granite in a public walkway, inside. The grout was smeared across the flamed grout, and was difficult to remove, but most of it i was able to remove with just simple soap and water(mostly water) and those steel scrub...
  13. W

    How do you get Even Adhesive Coverage on Tile?

    I'm now tiling a really uneven wall and I'm using up mountains of adhesive to make sure that its well supported and has an even spread to it, If I Just smear the adhesive on wall and go over with the comb side After I pull the tile off to see how much of the adhesive has stuck to the tile- I'm...
  14. C

    Cleaning and sealing a marble sink prior to installation

    We have a marble sink purchased from mandarin stone. Does anyone know the best cleaning products to use prior to sealing and installation? Any ideas on sealants would also be welcome. Thanks for taking the time!
  15. A

    My 1st Job Advice on regrouting/sealing

    Hello, I'm a novice to tiling and I'm looking for some advice on a problem I'm having. I'm trying to tackle some old grouting and sealant in my bathroom that has gone mouldy. Tried covering it up with some grout and silicon replenisher type product from Unibond, which has worked in parts but...
  16. C

    Mapei ultra colour grout coverage

    hi, Could anyone tell me what sq meter coverage I will get with a 5kg bag of mapei colour plus grout for the following :- 3mm spacers 300 x 500 tiles Thanks
  17. G

    Quartz floor tile sealing

    Hi, First post here. My name is Graham and I'm widening my DIY skills on my house in Kent. I have tiled the kitchen walls with a mirrored Quartz tile from a popular tile chain. I bought the adhesive and grout from them as they recommended. We have since decided to replace the slate floor tiles...
  18. J

    Split face wet look sealing

    Done a feature wall in split face, customer was dead happy with it. I've sealed it using fila pt10 wet look colour enhancer, which is the look he wanted. Any way he calls me up saying it's gone much lighter and the colour isn't as dark now. This is I've a week later. I'm thinking of getting some...
  19. W

    sealing around shower tray - best method or practice?

    I intend to tank plasterboard with mapei mapgum (or similar) and tape the joints as shown in this video below. It also shows the tape being bonded to the tray surface then tiled afterwards. Taking into account the thickness of tile and adhesive (which should obscure the joint) there would be...
  20. P

    Sealing and grouting encaustic tiles

    Just wondering if anyone else who's worked with Original Style might be able to advise. I've tiled a floor with their "black" and "white" encaustic 6" tiles and have sealed with Universeal All-in-one sealant. Went back today to grout but was getting some staining on the white tiles (cast iron...

Advertisement

Top