Hi
Had a lot of over boarding of ceilings of late so invested in a dewalt autofeed driver. Great bit of kit but wonder if its any use for fixing hardie board down. If anyones used it with sucess what screws are they using. Cheers
D
Hi
I have a client who needs me to tile his kitchen. Part of it is caber floor T&G (original part of the house) the other part (extension) is sand and cement screed. The extension comes off the front and side of the house so the join between the timber and screed is in an L shape. There is...
Hi,
Looking at tiling the floor of my bathroom. No UFH just plain tiling. Whats the preferred base?
Fixing onto solid floorboards (no squeak or bounce). Screwed down NMP or hardiebacker, or any other product suggestions?
Thank you for reading
John.
Hi All - on a new job today and I'm gonna need to raise the floor level further than the 12mm Hardie I'm installing will provide. So I'm gonna SLC it. The question is does it make any difference whether I install the Hardie then SLC over it, or lay the SLC then install the Hardie? I've never had...
Three sheets of Hardie Backer 1200m x 800mm x 6mm
Plus a few Wedi board off cuts
Free to collector
Less than 5 minutes off junction 11 of the M4
Thanks,
Simon
Hi there,
My first post! I've been following the forum a while at a distance! a great resource
Im renovating my bathroom (2mx2m floor) and I've got a question about SLC. The entire first floor of the house isn't level, it dips into the middle of the house and in the bathroom this means there...
Hi all. New to the forum. Hello everyone.
I've a studded wall in a walk in wetroom to tile. it's a nursing home, high humidity and high use. The wall has the shower itself on it. Everything else in the room is complete. I'm doing the studding at 400 centres for the uprights. I'm going to put...
Hi there
So quick question from a DIYer....
I am doing my en-suite. Now fully stripped. See pics
and to get the look without the expenses and work I would like to make it feel as "wet room" as possible.
Questions I have are....
FLOOR; I have a 25mm solid surface 900x900 shower tray, So was...
With hardie board can you lay ditra or tiles while the adhesive used for the hardie is still wet? I assume the screws will hold the hardie in place and am sure I've seen somewhere on a previous thread that this is the case?
Thanks
Quick question guys re 6mm hardie board going over 18 mm ply. I've been to 3 different topps tiles to get the 25mm hardie screws but they only have the 32mm which are too long. (Pipes etc). Can you use 20 or 25 mm turbo gold screws. I'm sure I saw something on here where some tilers do. Thanks
Got a wet room to tile inside the shower area and I'm unsure which substrate to use either Hardie backer board or moisture resistant plasterboard, two walls r brickwork one wall is studded
Got a job to quote for a customer who has specified that she wants the floor tanking. It's not a wet room or anything but she wants belts and braces approach, which is fair enough.
The subfloor is t&g floorboards, so was thinking of overboarding with 6mm Hardie and then tanking with paste and...
Hi
1st time post, newbie tiler after some advise.
I am planning on tiling the whole of the downstairs in a 3 storey townhouse, total area is around 30 square meters, have ordered 33 square meters of this porcelain tile. The room is kitchen / diner / family room, with a cloakroom and hallway...
As a tile fitter only - as I don't get involved in room prep prior to tiling, would it be down to me to tape and fill joints between backerboards before tiling or would you expect the installer of the boards to complete this proces or inform me that this proces is required?
Hi Guys,
My latest job I am back to brick/blockwork (again) due to weight of tiles and poor render/plaster. Now on a number of jobs I have used Hardie in the shower areas and MR plasterboard everywhere else. Using advice from the tile suppliers I actually D&D'd the Hardie to the walls on a...
Hey all,
I'm installing a shower tray with tiling upstand into a corner which has a solid wall one side, and some studded out hardie board (12mm) on the other.
I need to recess the shower tray slightly into the walls, in order to tank and then tile onto the upstands. Easy on the solid wall...
Hi All
looking at a bathroom today, all the walls need boarding which would either be fixed to joists or to brickwork, the customers looking at a tile size of 600x300mm, hasn't choose the tile, just the size!!! so could be porcelain.
Bath suite is out so no chew with boarding.
Green Moisture...
Having never done it, can you guys advise on a rough step by step guide for fixing marmox or hardie to different kinds of wall.
For studded and skimmed walls and for brick walls both plastered and not plastered. Need to know about the gluing and screwing for both instances.
Thanks in advance.
Tile Shop
Thread
aus
backerboard
fixing
hardiehardiebacker
marmox
marmox backerboard
method
plaster
tile backerboard
usa
wall
walls