shower tray

  1. johnbgoode

    Build shower pan over old wall tile?

    Hello, First time posting. I'm helping a friend of a friend who recently had a basement shower installed, and unfortunately the contractor who did it was completely incompetent. The floor of the shower is tile, and there is no slope to the drain (in fact if anything, there is a hump drawing...
  2. T

    Is our shower going to be ok?

    Hi all, We are DIYing our bathroom with a shower over tub. We waterproofed the wall linings, used a rubber upstand for our freestanding bath (sealux) and started tiling (80% done). I have a couple of issues with the work we have done... 1.We didn’t check tiles for coverage (I failed to...
  3. D

    Joining horizontal tiles to shower tray.

    I am retrofitting a 1200 X 760mm shower tray into an irregularly dimensioned shower room 1200mm X 1200mm X 1000mm X 780mm. The short sides are parallel and square to one long side. This leaves a roughly triangular area 1200mm long and about 30mm wide at one end and 240mm at the other which I...
  4. P

    Replacing shower tray - help needed.

    Hi all, I need to replace a shower tray. It sits on a base of plywood so I reckon it was glued. No access from underneath. Any recommendations on how best to do this? Brut force? Chisel and hammer? Or is there a more advanced way of doing this? The tiles sit on top of the tray - do I have to...
  5. craigy

    shower floor 2x2 mosaics

    Hi All, have a square drain cover in the center of a 3'x4' stall. Could the setting be started at the drain and work out to the walls? I just wanted full tiles around the square drain cover.
  6. T

    Cutting tiles for a wet room shower former

    Hi There, im about to start cutting my floor tiles for a wet room, i have a shower tray former with an end drain. The cut patterns are fairly self explanatory however am i right in thinking that dry cutting the 'fall cuts' is not an option? Im thinking wet cutting is required to create the...
  7. D

    shower tray plinth advice

    Hi all, just after a quick bit of advice. I am planning to install a shower tray onto a tiled plinth in similar way to the image attached. i haven't bought the tiles yet but i am about to build the plinth. Question:Should i avoid strips of tile less than a certain width on the top edge? I don't...
  8. M

    Discontinued tiles required for bathroom shower repair

    I require a pack of discontinued Pavigres Genciana Branco tiles for a shower repair (size 200mm * 250mm). Any help would be appreciated as currently at a dead end. Thank you.
  9. N

    Big gaps in shower wall grout

    I’ve just had a tile shower installed and went to clean it for the first time after it’s been installed. Haven’t used it yet. When I was cleaning I’ve seen a few big gaps in the grout in a couple of the lines. Also around the window the grout is all cracked and completely missing in most cases...
  10. R

    Advice Needed for shower set out please.

    Hi After a bit of advice from the pro's on how to layout new shower tiling project? We have 500x200 ceramic tiles. My thought was to have a full tile centred plus 2 x 445 cuts (2mm grout lines) either side on the front wall (1395) running vertically (not brick pattern). Each side wall is...
  11. TomMcgTX

    My 1st Job Tile above shower

    Hi all! I want to put tile above a shower in one of my bathrooms. The wall has paint and or plaster or something peeling off of the drywall, and has traces of mold showing (see pictures). I think the people we bought the house from 2-1/2 years ago did a quick patch job to try and make it look...
  12. D

    My 1st Job Tile a shower floor area using 600 x 300 tiles

    Which Tile layout is best using 600 x 300 into a shower area measuring 900 x 900 with waste in the middle of the floor
  13. craigy

    Large format rectified polished porcelain with no Grout in a shower?

    I am a non pro who has been asked to set some large tiles on a shower wall tight. is that recommended?
  14. M

    Shower room large tiles. Where too start

    Hi, I’m about to start a shower room job. I’m using 1200mm x200mm tiles vertically. So it will only be 2 high each row. What’s the best way to start. If the tiles were smaller I would use a baton to get my level but wiith only 2 high, not sure the best way to start. Should I use a baton and...
  15. P

    Desperate for advice on our Travertine showers.

    Hi all, I'm faced with a bit of a conundrum regarding the state of our shower recess, as well as my partners parents en suite shower. The posted images are just of the major issues in the main bathroom aka ours, and it has been cleaned, scrubbed, anti-molded to high hell and this is what...
  16. P

    Fitting shower screen to wall above tile sloping to bath edge leaves a gap

    Hello Tilers I recently fitted a bathroom for a (paying) friend. One of the problems I encountered was the soil pipe which runs behind, then turns to run along the tap end of the bath. I made up the gap with 76 x 51 mm (3''x 2'') CLS, I tiled it forming a slope to shed water, grouted and then...
  17. N

    Replacing Silicon around shower tray

    I just bought a house and noticed the stone resin shower tray is leaking. The Silicon job is pretty crap so I started removing it with the aim of redoing it properly but noticed the shower tray is still wrapped in plastic around the edges meaning the Silicon hasn't bonded to the side of the...
  18. W

    Disaster shower wet wall

    I had my bathroom tiled and fit by a “bathroom fitter, tiler and plumber with 14 years in the industry” in 2018 and he did some pipework elsewhere. He’s registered with a chartered body. His work has been poor, he’s since come back and ripped it all out (except the shower) and just left it. I...
  19. H

    re sealing shower

    Hi I need some advice on re applying sealant in my shower. We have had some movement and a gap in the corner of the shower has appeared (I've attached a picture) The gap is over 7mm. How would be the best way of re sealing this? I was going to use CT1 sealer.

Advertisement

Top