Discuss The use of chicken wire in tiling in the Canada Tile Advice area at TilersForums.com.

W

White Room

I used it too! I'm only 35! When I started with the old man moo he used to ply out floor and staple expanded metal/ chicken wire to the floor then tile if I recall, last one was in '98 if memory serves. Tiled a dance floor of a nightclub in Maidenhead with it, Michelle Gayle opened the club, I spent most of the time getting coffee for the whole site from the local Wendy's!! Ah Halcyon days .........

Who's she ????
 
O

One Day

Who's she ????
bo+selecta+mel+b.jpg
 

AD Ceramics

TF
Esteemed
Arms
269
758
Manchester
I used to do pub refurbs all over the country years ago and I always used 8x2 expamet sheets fixed to floor boards with galv plasterboard nails then latex leveller over the top, then tiled with x7 and ardion 90. You'd have to rip the whole floor up to get it up, I went to a boozer I did 20 years ago and a large floor area of reclaimed quarries was still down and not a crack in sight and the place had been refurbed a few times since.
 
I used it too! I'm only 35! When I started with the old man moo he used to ply out floor and staple expanded metal/ chicken wire to the floor then tile if I recall, last one was in '98 if memory serves. Tiled a dance floor of a nightclub in Maidenhead with it, Michelle Gayle opened the club, I spent most of the time getting coffee for the whole site from the local Wendy's!! Ah Halcyon days .........


Smokey joes by any chance?
 
T

Time's Ran Out

If it wasn't for the cost I think a lot of Tilers would still be using the combination of X7 and ardion 90.

Last time I used chicken wire was in 1976!
Gents toilets, Indian restaurant onto a t&g floor that you could see the cellar through. Put down waterproof building paper, staple nailed wire through to wood, 2 and half inch dry mix sand/cement, cement slurry back of quarries, and tapped into place.
Went back last week and the whole place has gone!
 

GAZ5518

TF
Esteemed
Arms
142
558
EPSOM
Gotta say those old ways ( where I come from) were tried and tested and were the "proper" way to do things .. then...(those floors are a ***** to remove)....totally agree about X7 and Ardion 90... Stuck like s##t to a blanket.... ....:musicalscore: "Those were the days my friend , we thought they'd ....la la la":musicalscore::musicalscore:;);)
 

Reply to The use of chicken wire in tiling in the Canada Tile Advice area at TilersForums.com

Subscribe to Tilers Forums

There are similar tiling threads here

I had a small leak in the main water line before the stop tap in my 1950s house. The copper pipe...
Replies
1
Views
2K
Just seen Rocatex on uHeat.co.uk and thought hmmm that's a new one on me. Anybody used it yet...
Replies
3
Views
2K
    • Like
  • Sticky
Hi there - I’m hoping to get some advice. I’m a builder, based in Melbourne, Australia. I’ve...
Replies
12
Views
5K
Matthew7
M
Hello guys. I came upon and registered with this forum while doing some research on decoupling...
Replies
3
Views
5K
hats67 - Yesterday at 11:48 PM Add bookmark #1 Hello guys. I came upon and registered with...
Replies
1
Views
3K

Advertisement

Thread Information

Title
The use of chicken wire in tiling
Prefix
N/A
Forum
Canada Tile Advice
Start date
Last reply date
Replies
37

Thread Tags

Which tile adhesive brand did you use most this year?

  • Palace

    Votes: 9 5.8%
  • Kerakoll

    Votes: 15 9.6%
  • Ardex

    Votes: 11 7.1%
  • Mapei

    Votes: 46 29.5%
  • Ultra Tile

    Votes: 19 12.2%
  • BAL

    Votes: 37 23.7%
  • Wedi

    Votes: 4 2.6%
  • Benfer

    Votes: 2 1.3%
  • Tilemaster

    Votes: 21 13.5%
  • Weber

    Votes: 18 11.5%
  • Other (any other brand not listed)

    Votes: 17 10.9%
  • Nicobond

    Votes: 7 4.5%
  • Norcros

    Votes: 3 1.9%
  • Kelmore

    Votes: 4 2.6%
Top