board

  1. E

    primer on backer board

    hi all going to use cement backer boards my question is do i primer both sides? im fixing using tlie adesive and screws to wall thanks george
  2. E

    backer board joins

    hi all when using 6mm cement backer boards on a wall do i have to use tape on the joints or just skim them with tile adesive i will be tanking anyway? thanks george
  3. T

    Insulation board fixing method

    Hi, whats the normal method of fixing jacko/wedi board to timber floors. Ive used these boards a fair bit before but never on floors so im unsure on what way round to do it... Do you set them with rapid set then add the fixings while the adhesives still wet or wait until its set and then add...
  4. L

    Kerdi Board - painting on

    Hello I'm half way through doing my bathroom with Kerdi products. One of the walls will be half tiled and half painted. Reading around Kerdi is no good for taking plaster (it cracks etc) and so you can't really paint on it. So my plan is to cut it out and put some regular board up so I can...
  5. D

    Thinnest backer board? 3mm ply?

    Hi, I'm looking for a super-thin backer board, in order to tile a stud wall on both sides and have one tile (60mm wide) on each end. Haven't found anything less than 6mm, so I'm wondering whether I have to go with 3mm ply (not a recommended substrate I know) The stud wall is only 600mm long...
  6. A

    Impey former and backer board installation

    I'm doing a wet room and I am just about to lay the Impey aqua dec linear 2 shower former and attach tile backer boards to the stud wall. I feel that I should put the former down first, butted right up to the studs in the stud wall then install the backer boards so they hang over the lip of the...
  7. P

    Wedi board behind wall hung pan

    Hello gents! Long time lurker, first time poster.... I’m just fitting out our en-suite bathroom using Wedi board on three walls and standard plasterboard on the fourth. Most of the Wedi will be plastered and painted with only the shower area being tiled (I’ve used Wedi all round because of the...
  8. R

    Forgot to mortar down insulation board to floor....

    Hi, I bought some sheets of 6mm insulation board to install on my bathroom floor. (It has blue foam in the middle of it.) My subfloor is 21mm treated wooden floorboards. I've freshly installed them and they're nice and level and smooth. (I even planed some of the joists to make sure I'd have a...
  9. J

    window - best trim to finish metro tiles

    Hi all, tiling my kitchen and I am upto the window. what the best way to finish where the tiles turn in toward the window. These are metro /subway tiles and have beveled edges, so will vary in thickness where they are cut at the window recess - what is the best trim to use or is it possible to...
    • jans
    • Thread
    • best board metro metro tiles tile tiles trim window
    • Replies: 3
    • Forum: DIY Tiling Forum
  10. J

    My 1st Job Cement Board Tiling Challenge!

    Hi Everyone, 1st time bathroom install around a bath. Current stud wall with tiles removed has had it, I'm taking out the plaster board and replacing with cement boards (already purchased). Question: When cement boards are installed, I am going to tank it using "Aqua Seal Tanking kit". Before...
  11. S

    65mm cement board screws?

    Hello all. My building inspector told me i have to insulate over my stud uprights to avoid cold bridging(25mm pir). This side of the wall will be bath and shower so wanted to use hardiebacker boards to tile over. I cannot find any cement board screws long enough to secure the 12mm board over the...
  12. J

    Use plywood behind tile backer board?

    So I'm about to box in some pipes and tile over them - I understand that tiling directly onto ply is bad obvs - just wondered if it's advisable to box in with ply and then overboard with tile backer board or do most tilers just go with board directly?
    • jonhamil
    • Thread
    • backer board board canada plywood tile tile backerboard
    • Replies: 1
    • Forum: Canada Tile Advice
  13. J

    Hardibacker vs STS / Wedi tile backer board

    I have a fairly small bathroom 2m x 2.2m which will be tiled wall to floor all round. The straight bath will be fitted onto the 2m wall so I will need a tile backing board. I will be going for porcelain tiles - not sure on the weight but size wise will be 600 x 300. The bathroom is back to...
    • jleag
    • Thread
    • backer board board hardibacker tile tile backerboard wedi
    • Replies: 4
    • Forum: DIY Tiling Forum
  14. F

    Underlayment Question - Backer board ok on top of felt/metal lath?

    Initially planned on a mortar bed for my underlayment. Quickly realized I should've gone with backer board instead. I already installed roofing felt and metal lath. Is it ok to install the cement board on top or should I rip out the paper/lath? Thanks in advance. -Frank
  15. T

    Wedi board

    Hi team I have hacked off one tile approx 40cm by 20cm off a bathroom wall that's covered in tiles head to toe The surface of the wedi behind this tile and it's netting has come off with the tile and it's adhesive. Considering the incredibly small area concerned (one tile), is there a best...
  16. C

    Thermal Cement board vs Sand & Cement render prior to tiling on brick wall

    Hi All, It's my first post here. I'm currently working on a wetroom in my flat and would love to hear your advice. 2 sides of the wetroom are pretty straight forward and are going to be tiled onto thermal cement boards fixed to timber pre-wall. Other wall is was old plaster stripped to brick. I...
    • cexec
    • Thread
    • board brick canada cement cement board render sand tiling wall
    • Replies: 1
    • Forum: Canada Tile Advice
  17. R

    tile board over wet ufh

    Is there a board that can be used to screw to the joists in wooden floor (with a wet ufh system)? - im hoping theres a 6mm product out there to bring a small area up to the adjacent screed height. Can anyone suggest anything. Thanks
  18. A

    Aqua board /Jackoboard to plastered walls

    The walls are already plastered, I know it’s better if they hadn’t been, can I just mechanically fix the boards or do I need to used adhesive as well also if I do need to use adhesive do I need to prime the plaster first if so what with Thanks
  19. J

    Tiling onto JG Overfit board

    Has anyone ever put a self levelling onto JG Overfit UFH boards. They are a 25mm PIR board, foil lined with 15mm pvc pipes running through. Instarmac suggest their LevelIT2 can be used however JG say no products should be used.
  20. G

    Should I board

    Hi, I am going to tile my sons bathroom where most of the the skim plaster has come off when removing the few tiles there were and the rest of the bathroom is covered in artex, which is quite old and probably contains asbestos. Under the plaster is a very absorbent soft plaster, I asusme this...

Featured Threads

Advertisement

Back
Top

Click Here to Register for Free / Remove Ad