board

  1. M

    Subfloor preparation - matting vs board on plywood

    Bit of an intro - I'm a competent DIYer and have been refurbing the bathroom on and off for the last few months - currently the only bathroom in the house so am refurbing around the family using it, hence it's taking a while. So I've got the shower cubicle in and installed (tanked and tiled) -...
  2. 1

    Cement Board Jointing and Tanking ?

    Please help. I’m about to tile a small two-sided shower area, 2.5m high and width 1.2m one way and 2m the other. Tiles are conventional ceramic Substrate is 6mm Hardie Board glued and screwed onto original plywood to one side and plasterboard to the other. Hardie recommend using their fibatape...
  3. acaciaguy

    Does tile mister delta board need priming

    Hello all Does tile master delta board need priming before tiling on to? Many thanks.
  4. M

    How to cover/work round copper pipes?

    Hi All, Installing Marmox boards in a shower area and want to avoid a stud wall to keep as much space as poss. Will carry on with dot and dab (uneven old walls) for the boards but what advice could you give for where the shower pipes are? If i was to cover them then the boards would sit out...
    • Matty
    • Thread
    • board canada how job jobs marmox tiling jobs tiling work work
    • Replies: 4
    • Forum: Canada Tile Advice
  5. D

    Floor Level under Go Board for Floor

    I'm tiling a small bathroom floor (8'x10') which is not level (1/2 low at the one end). I plan on using the TEC EZ floor level and then putting go-board on top of that. I'll thin-set the go-board in to the subfloor and leveled Tec EZ floor area. . When reading the go-Board for flooring...
  6. O

    BAL Board under shower tray

    Hello! New to the forum and my first post on this after doing a bit of searching. I'd be interested to know your thoughts/experience of fitting BAL Board or Hardiebacker under the shower tray. The reason I ask is that with the build-up i'm looking at, if I installed the shower tray on the ply...
    • oliversimon
    • Thread
    • adhesive bal bal adhesive board building adhesives former grout shower shower tray tray under wetroom
    • Replies: 3
    • Forum: Tanking and Wetrooms
  7. dg-1984

    Angle grinder cutting on top of a board

    I was watching videos on cutting tiles with angle grinder and came a cross one where the tile was cut on what looked like a large board. Anyone know what material it would be looking at getting something to cut on top of.
  8. M

    Foam boad vs cement board

    What do you pros on here use most then? Ragrdless of customers budget and you choose msterials Xps foam.boards like jackoboard,marmox weidi etc Or Cement boards lile hardie, no.more ply etc with tanking where applicable Or Plasterboard just to throw it in there.tanking where needs be. Dont...
    • MAK_Tiling
    • Thread
    • best board canada cement cement board foam hardiebacker marmox plasterboard tanking
    • Replies: 18
    • Forum: Canada Tile Advice
  9. T

    Q Board under floor tiles

    Has anyone used the Q Board for floors? I was going to put 10mm Q Board over wooden floor boards and then lay floor tiles onto it. I've been researching the product (s) and it appears to be a good system and fairly inexpensive too. Has anyone had any experience using this product on a floor and...
  10. H573

    Difference between Jackoboard and Wedi board

    Hi all, So basically what’s the difference between Jacko and Wedi?
  11. B

    Orbry board

    First time I’ve used Orbry board and seems a good product and reasonably priced. One quick question, when using it with the orbry self adhesive joint tape do you need to paint tanking membrane over the tape? The instructions just say tape the joints to make it waterproof. This is for a shower...
  12. D

    Plywood for tiling on floors? or Tile backer board?

    Hello everyone I have a question reguarding ply for floors. It states that it has to be WPB but my question is where do you buy this ply from. Jewsons ply does not state it is WPB and the ply in wickes says nothing too just that it's sutible externaly if coated with a protector. Please can you...
    • Dan1234
    • Thread
    • backer board board canada floor floor tiling floors plywood tile tile backerboard tiling
    • Replies: 43
    • Forum: Canada Tile Advice
  13. M

    What to wall and floor board

    Hi guys. Planning my build ready for 24th this month to get it started so i am trying to get fully prepared. I posted a thread on what tray to go with but thats sorted now. I am going to be shelling the room out, its very small at 1.5m x 1.8m. Theres a stud wall on one side of the shower...
  14. F

    Polishing a granite chopping board

    I've been nagged for quite some time to polish up a granite chopping board that has gone very dull. Not something I've done before, can anyone advise on if the results will be good with dry diamond pads and if so what grades ?
  15. N

    Installing Extruded Poly board

    Are all the extruded poly boards fixed with tabbed washers? The photo attached is a showroom example, where they haven't used washers anywhere, an important detail I thought. Surly not using them, there is potential for failures there????
  16. G

    Tilebacker fixings sitting proud of board

    Hi, I've used Fischer hammer in fixings to secure Gyproc tilebacker to a masonry wall. The fixings sit proud of the board by approx 3mm (12mm dia). Will this cause any issues when tiling onto the board? The tiles are 1200x600mm and weight 17kg each so need to be sure before installing.
  17. F

    Bulk buying screws for backer board

    Just wondered if anyone bought bigger quantities of screws for boarding floors ? I have a couple of large floors to board and the usual turbo gold screws only seem to be available in boxes of 100, any decent alternatives ?
    • Flintstone
    • Thread
    • backer board board bulk canada screws tile backerboard
    • Replies: 16
    • Forum: Canada Tile Advice
  18. G

    22mm tile board availability?

    Hi, I'm a DIY'er having stripped my bathroom back to joists and nearly ready to lay the floor. My preference was to use 22mm NoMorePly or GIFAfloor boards direct to the joists and then tile direct to the boards, but I understand NMP is no longer available in UK? I've seen references to GIFAfloor...
  19. Bbbecca7

    Tiling bathroom floor- floorboards/cement board question

    Hi all! Since everyone was so helpful with near tiling disaster last time I am hoping to get a bit more advice now that we are coming to tile our bathroom floor. We want to make sure we do it right first time! The floor of the bathroom is wood floorboards. They're in relatively good nick and...
  20. L

    Adding moisture board to walls for tiling

    Hello all. I am after some advice. I am doing a bathroom job and have discovered that the walls are made of corrugated cardboard with plasterboard either side and then more plasterboard dot and dabbed onto this using multi finish. This extra layer has been removed and I want to add green...

Featured Threads

Advertisement

Back
Top

Click Here to Register for Free / Remove Ad