I normally use marmox i find it a good product to work with nice and light to use easy to cut and quick to install and have never had a problem with it untill now:mad2:
What a let down, I had 50mm boards delivered and i use 50mm loosely! The thickness betwenn the boards varied from 46mm-53mm...
peckers
Thread
backerboardmarmoxmarmoxbackerboard
out
tile backerboard
usa
hi peeps,i have to create a 3 peiced bath panel for 3 sides of a steam cabin..all are to be removable and i also need curves for going round to suit the sahpe of it,,do kerdi boards and marmox boards do such a thing as a board you can shape to suit? i have only used the straight wedi boards...
Hello
Has anyone got any experience with Marmox Board CS?
Apparently it has a rubber backing which offers enhanced acoustic properties over the standard boards which is what I’m looking for when I replace the acoustic overboard floor in my flat.
:thumbsup:
Hi,
Flooring a wetroom and planning to use 20mm Marmox ray and boards but I don't have enough room under existing floor for shower waste and pipe so was thinking of layering floor first with 50mm Marmox boards then laying down the Marmox 20mm tray and 20mm boards on top of the 50mm boards. Will...
lylemes
Thread
backerboard
boards
marmoxmarmoxbackerboard
tile backerboard
usa
hello all,
I'm about to lay 10mm marmox insulation boards onto 12mm ply.
Do I just stick them down using flexible tile adhesive, or is it also wise to screw them down at 300 centres.
If screwing, will the plastic backboard washers be fine with the UFH?
regards
ap222
Thread
backerboard
boards
down
floor
floor tiling
laying
marmoxmarmoxbackerboard
tile backerboard
usa
Hi
Im after a bit of advice, Im Installing a pre fomed Marmox shower tray but in the instructions it says all thats required due to the tray being waterproof is to apply a membrane tape over the joint of the tray and ply floor then tile as normal.
Do you guys have any experience with this and...
OK got marmox shower tray for bathroom and intend to have it level with floor.
1. Plan is to have WEP 15mm ply on floor screwed every 300mm and moisture resistant plaster board on walls.
2. Insert tray and bed into flexible addy and fit drain sealing arund drain with Silicon.
3. Tank both...
I am new here and i have a question, and hope you can help
I am a bit confused about how to fix these marmox boards
The underfloor is 20mm boards, then 12mm ply en then 6mm marmox boards
these marmox boards will be fixed as well with screws and washers
but what kind of glue, or setting...
Mcluma
Thread
backerboard
boards
fitting
marmoxmarmoxbackerboard
tile backerboard
usa
Hi all
Thoughts would be appreciated from anybody whose used Marmox backer boards before on walls before.
First time i've used these products before and have looked them up.
In the shower enclosure one wall is stud and the other block.
I looked at the Wedi manual and they say a minimum of...
kaharrison9
Thread
backerboardmarmoxmarmoxbackerboard
thickness
tile backerboard
usa
Hi
As previously discussed in this thread I am going ahead with a stone floor to replace my previous oak one that has been scrapped following a flood. (boo hoo - I prefer wood)
OK nothing ideal about this situation I know, but we cannot go through all the disruption again so want to get things...
Noreng
Thread
backerboard
limestone
marmoxmarmoxbackerboard
tile backerboard
usa
wedi
Good Morning
I have an existing shower enclosure 3 x internal 4 inch blockwork walls bonded and skimmed which is 770mm - 775mm wide, it used to house an 800x800 tray which was very badly installed, cut into the walls and then a 760 bifold door installed at the front.
I want to put in a...
Gazebo
Thread
backerboard
installation
marmoxmarmoxbackerboard
tile backerboard
usa
Hi
A question for the forum.
I have removed old tiles from a shower enclosure including plaster, horse hair etc (property built in 1860) leaving very uneven brickwork, non cavity. To level up with the rest of the wall would be around 20mm, my question would be your thoughts on whether to use...
ACS
Thread
backerboardmarmoxmarmoxbackerboard
tile backerboard
usa
Hi,
I'm thinking of using Marmox 20mm backer Boards to do a shower enclosure. Are they any good?
One side would be fixed to a wooden frame and the other two fixed with tile adhesive to a 10mm layer of one-coat plaster over old, uneven bricks (it's a 1000mm tray to go in a 1060mm wide room)...
dangertomyself
Thread
backerboard
boards
marmoxmarmoxbackerboard
shower
tile backerboard
usa
Hello Everybody, I would like to introduce myself and my company, My name is Jonathan and I work for a company called Marmox Uk Ltd, for those of you that do not know what we do at Marmox, we manufacture and supply to the industry a range of Insulated and waterproof products that come in the...
Marmox Tech
Thread
backerboard
hello
insulation
marmoxmarmoxbackerboard
tile backerboard
usa
waterproof
i'v got 80 sheets of marmox to fit soon, most of it on concrete, and some onto a bitumin screed. I know onto concrete it is pretty straight forward, Prime and bed on spf, but i'm not to sure about the bitumin screed if anyone can give me advice on this i would be grateful. Thanks
Hi guys/girls
I am looking for a good price on marmox 10mm and cable kits, marmox for 45 sq mts and cable 35 sq mts, I use varme but maybe someone knows a better deal, I don't want the mats.
:thumbsup:
diamondtiling
Thread
backerboardmarmoxmarmoxbackerboard
tile backerboard
ufh
usa
Has anyone one installed a marmox showerlay showertray? or had a look at one,what do you think of the build quality?,they seem very cheap compared to say an impey tray £70-£80 as against £300 for a 800x800?.What trays would you recommend? Thanks Phil.
59peejay
Thread
backerboardmarmoxmarmoxbackerboard
opinions
tile backerboard
usa
Alright everyone , I was wondering if anyone has used marmox boards as apposed to hardi-backer ,How easy is it to use and whats the normal procedure for walls? Cheers for any help given
cct
Thread
backerboard
boards
marmoxmarmoxbackerboard
tile backerboard
usa