out

I’m going to start my bathroom refit this weekend and just want to check my plan is sensible. I’m using 300x500mm ceramic tiles, floor to ceiling, no border. The wall tiles are mainly pale, the floor tiles are dark and I was planning on creating a 100mm dark tile upstand all around. The room...

Could anyone help?? I am searching for a Tile that Wickes no longer stock. I bought this specific tile 3 years ago and would like 20 SQM more. Would anyone know how I could find these ???? Timber Dark Beige Porcelain Tile 15x60 cm Shade : 0 Caliber : 2 Help would be greatly appreciated

Hi everyone have been tiling for five years all qualified am just setting up my first buissness in devon any advice would be appreciated where's best to advertise sub contracting invoicing etc cheers

Hello, I’m thinking of Tiling the bath wall in my bathroom as a feature in herringbone 45 using 200 x 100 porcelain tiles. The witdth of my bath is the same with as the wall. The wall is flat and has been plastered. Looking for any advice on, -Where to start? As in work up from the bath or...

Having a new utility room fitted, by a builder. The room has just been plastered. The wall in the room must be wonky, I think. The sink has just been fitted. It's 5cm from the front of the worktop on each side. However, at the back, one end of the sink is 5cm from the wall and the other end...

Hi guys, I finally have some walls and levels to work off for setting out. Here's the wall I am finding a bit tricky: Sorry for the squiffy angle, it's a small room. Here's a plan with dimensions: Tiles are 500 x 200, laid stacked, long side horizontal. 2 mm grout joints. I'm fairly...

Just been past Stonehenge on the way to work this morning at Artisans of devizes and they are all queuing to get in . Don' think its going to be a very good one it's a bit murky here .

Hi My builder didn't bother doing this, meaning I will have to. What is the most effective way of clearing this out, as I have 28sqm to rectify. Without doing this, don't know where the grout supposed to fit, so not too sure why this wasn't done. Any advice appreciated would be great...

hi all, did a bathroom and a kitchen floor this week. Used standard set addy which gave me a bit more time to work. Left it for a good 24 hours before grouting Plywood subfloor installed by joiner and sealed with latex sealant by me before being left to dry and then tiled. Grout in bathroom fine...

Quick one to check I'm on the right track - I'm planning to do a tiled bath panel (with access panel using some Schluter magnets). Am I right in thinking I should have cuts below the bath rim and cuts down onto the floor? It'll be about 560 mm high, tiles are 200 mm high, so I'm thinking to...

Helping a friend out with a small bathroom and one of the walls is pretty uneven and not particularly plumb. I've levelled it out with a bit of rapid set to get it flatter but wondered what you guys do with regarding getting it plumb. Its not massively out, just want to get it as good as...

Hi, I need a bathroom tiling in the next 3 weeks. Its in Monk Fryston which is near Leeds / York / Tadcaster / Selby / Goole etc I did the en suite and my wife isn't happy with the finish (admittingly its not good - so i am in the dog house!) and the house is going to be carpeted in 4 weeks...

Dear All, I have recently has procelain tiles laid in my downstairs area which is around 80sq.m. We have UFH (water based) installed as well. The builder has was Lafarge (anhydrite) screed. He has allowed enough curing time (3 weeks) and heating was commissioned in the right way (starting...

Hi, I'm struggling to decide between these floor layouts. I've gone for staggered patterns so I can avoid intersecting with the grout lines on the walls. The floor tiles are 900mm x 450mm with 3mm grout line. The floor is 2460 wide by 2270mm long , the bath is 800mm wide by 1800mm long...

As the title. I have my daughters kitchen splashback to tile. In the examples Ive seen the worktops seem to be taken as level and full tiles (metro) form the bottom layer. My question is how do you address if the worktop is not level? Do you mark a line about half a metro up and cut the bottom...

I have a TS40 that is running out of square by 1mm over 300mm........not much,but not much cop if you have to do repeated parallel cuts. So, can it be corrected with the aid of the screws either side of the breaker mechanism?

Moving to oz soon and they seem to have falls in most rooms in their houses. Just wondered how other people work out their falls and letterboxing etc. Cheers guys

Hi there, I've been emailing tile companies and none seem to be able to offer me any advice on my query. So I thought I'd ask the experts in here! I'd like to tile the lid/top (hinged to access record player) and base of a hi-fi cabinet that I've renovated. As far as I could see it's either...

I was working in retail last year and quit my job to become a laborer. I took a hit in terms of money but wanted to better myself. I've been given the opportunity to learn tiling. I did a few bathrooms with my boss helping me and then recently I tiled a full bathroom on my own, granted it was a...