I need to tile 3 sides around a bath with a shower going into it. Two of them have been stripped back to brick and the third is a a stud wall.
Has anyone tried the new Wickes Tile Panel which is made by Knauf for Wickes and is £15.49 for a 4 x 3 sheet...
Hi all,
Hope you can help me on this one!
I have installed a bath with a curved end and want to use slim vertiacal sections of porcelain tiles to create a faeture rather than use a plastic matched board.
So I need to create a curve with a flexable material with as small a depth as possible so...
I know this has come up loads before but I need advice please as I can afford any mistakes my name must remain perfect it's not that I can do the job it's just I've never needed to do it as I've always done new builds ok now the defence is done as I said in a previous thread I have a bathroom...
I need an access panel in a floor for the stop ****. I have seen plastic ones for walls but nothing for floors. What i need is something like a galvanised steel tray/frame to house a 300mm tile bonded to a piece of ply which can be set into the floor. I does not need to be hinged or anything...
I'm planning on fixing some 10mm glass with clamps such as these http://www.crlaurence.com/techdocs/PDF/UC77.pdf floor & ceiling but wondering how to fix to the floor without damaging the Dura C++ matting.
Can anyone advise on the best way to do this? Is there a way of fixing to the face of...
Hi guys, after a bit of advice please. Im setting out for some 305x305 trav.
Now... do I
A) work it so the flush mount is directly in the middle of the tile (tricky cut!)
B) work it so half the tile meets the middle of the mount
what would look better? I cant decide! :mad2:
Thanks v much
Dave
When 'popping off' the (very well fitting) bath side, it flexed a little too much and I managed to get a tiny tear (5/6cm).
It will be out of sight when done and it's really not worth a new panel, so...
Has anyone ever patched up such a tear successfully?
& if so, what with plse? (Type of...
Morning all! I've been asked to tile a slate bath panel using 600x300 ceramics. The panel has probably been on there for about 50 yrs and when I prime it it just runs off. Does anyone have any experience of tiling onto slate and if so what procedure would advise I followed in order to carry out...
Hi All,
I have boarded a wall with aqua panel, dot and dabbed and then plugged and screwed to give a mechanical fixing.
Despite best efforts in ensuring all boards were level and no lippage between the joints, one of the boards seems to have pulled in too much along the top . I’ve put a...
rupert
Thread
aus
format
large
large format
levelling
out
panel
tiling
usa
wall
wall tiling
Hi all, our plastic bath panel was cracked so I decided to get rid of it and make a panel that I could tile, now I have secured the bath as much as possible using 2x2 and its solid and I have approx 40mm extrusion from side of the bath to tile onto if you know what I mean (had to bring a lip out...
Hi peeps,Ive a job coming up where i need to fix glass mosaics to the front of a curved bath.I know marmox do a curved panel for this.Has anyone tried and tested one of these or is there any other curved panels on the market which could be used ?:smilewinkgrin:
Hello. I have had Wunda overfloor heating panels installed to approx 70m2 area. When the flooring company came to lay our quickstep laminate arte floor tiles (640x640) they said the floor wasn't level enough as many of the underfloor heating pipes where raised about 2-3mm above the aluminium...
Clifflev
Thread
adhesive
aus
floor
grout
mapei
mapei adhesive
mapei grout
panel
problem
screed
usa
I have seen a floor channel with a solid rubber insert about 12mm wide, this was in a changing room floor for a swimming pool and was used to divide the changin room floor tiles and shower/toilet area floor tiles. Both wet areas.
I want to use part of the channel to hold a glass shower panel...
Ok so, I tile a bathroom. At the end of the bath is a gap approx 500mm between bath and wall. 100mm up the make a raised floor so to cover the waste pipe. The floor is tiled too, and I carry the floor tiles just under the bath so as bath panel sits on the floor tile. Same with this boxing where...
Hello chaps and chapesses, anybody know where i can get my hands on 20mm travertine, filled and honed measuring 740mmx170mm.
Anybody got any off cuts lying around? I just need it for a WC access panel shelf, i can polish the edges myself.
Been to a few local stone places but no joy, am in the SE...
hello all.just after a bit of advice about finishing a tiled bath panel.do you finish the panel flush with the front of the bath or do you come up under the top rim of the bath or, is every bath different? thanks in advance, dave.
Looking for a bit of proffesional advice, I need to tile a bath panel, standard size bath. Would 9mm or 12mm ply be ok ? also is a standard tile adhesive ok on the ply if ply is to be used ? thanks in advance. :thumbsup:
Hi,
Am on the final straight of my wetroom project!
The wetroom is fairly small (2.5x2.0m) and there is a bath fairly close to the shower area, so I am expecting the bath is going to be splashed by water when taking a shower.
I want to fit glass panels to the side and end of the bath and...
ojtiler
Thread
aus
bath
bath panel
frame
glass
metal
panel
tanking
usa
waterproofing
wetroom
wetroom tiling