screws

I've stuck a 12mm hardiebacker board onto a brick wall with adhesive & will be screwing it to. Which screws & what size should I use for this?

Ive got a box of jackoboard galvanized washers ready to start fitting the boards but not sure what screws to use.... all i can find on their pages are 'used suitable screws' will something like galvanized turbogolds/goldscrews be good enough. I was thinking od stainless screws but since the...

My Omnie TorFloor UFH is now in place and has been filled with water at mains pressure with no leaks, so after the pressure test tomorrow I'm ready to overlay the 22mm chipboard with 9mm ply, which will be glued and screwed. I know fixing plyboard over UFH isn't a great idea but it is required...

Hello all. My building inspector told me i have to insulate over my stud uprights to avoid cold bridging(25mm pir). This side of the wall will be bath and shower so wanted to use hardiebacker boards to tile over. I cannot find any cement board screws long enough to secure the 12mm board over the...

Are theese screws ok for marmox 12.5mm boards for walls pic attached. If not which are best recomended.? And which washers are better the metal ones or plastic? Thanks :thumbsup:

Just wondered if anyone bought bigger quantities of screws for boarding floors ? I have a couple of large floors to board and the usual turbo gold screws only seem to be available in boxes of 100, any decent alternatives ?

will these stainless screws be ok for hardie backer? https://www.screwfix.com/p/ultra-screw-pz-double-countersunk-multipurpose-screws-4-x-40mm-200-pack/79985 Do you need to drill pilot holes?

Hey, all Just wondering if you need washers for installing 6mm boards like Norcros pro board, Wedi, Mamrox, Kerdi etc (not hardiebacker) Onto a solid wall? How would you install 6mm backer board to a solid wall? I Just don't want to order washers for nothing.

Hi, just a quick question. What screws should I use/you use on new cement boards in the bathroom before tiling? The Hardie screws are not that great I'm told, do you have any links to screws good for mounting the panels to the wall.

Silly question perhaps, but when you're applying a liquid membrane (aquadefense in this case), do you just apply it over the screws that were used to fix the boards. Or do you cover the screws in a little tape or something? Also, when you've finished the tiling and grouting, and say you're...

Hi, looking for some quick advice about tanking plasterboard ready for tiling. The area is going to be a shower. What are you supposed to do with the screw heads that are not on a join? I'm using the mapei wpk, which gives no instruction on this point! Do I just paint the membrane over them...

tried them out today, Crap! Not a patch on the propper no more ply screws, they don't counter sink in half as nice. I know they are cheaper but still, screw heads sticking up is no fun

Hi 1st time post, newbie tiler after some advise. I am planning on tiling the whole of the downstairs in a 3 storey townhouse, total area is around 30 square meters, have ordered 33 square meters of this porcelain tile. The room is kitchen / diner / family room, with a cloakroom and hallway...

Hi I know Screwfix turbo gold screws have been mentioned on this forum to secure 12 mm cement board. I will be using these screws to secure the 12 mm cement board to wood. But I also have to secure the 12 mm cement board to metal stud framing. Which screws do people advice please to use, to...

got quite a big floorwhich needs overlaying with xl cement board(trinmline) similar to hardibacker. just found the screws delivered too long for heat pipes below. whats the best type of screw for these boards . screwfix is open and my best bet today. any suggestions

I have read that the alkali in the cement board can slowly rust a screw over a period of time. The screwfix turbo gold screw says it is zinc & yellow passivated for double corrosion resistance. Could I please check if this screw is OK to use to fix cement boards? Or should I be using the...

Hi All Ive not been on for a couple of years. The last time I was tiling a full bathroom at home and found your advice fantastic, (must get some pictures uploaded) Well I have moved house from York down to Surrey and guess what its DIY bathroom time again. I have re-screwed down the existing...

I'm over boarding a ply floor with 6mm backer board in a couple of weeks time and wondered what fixings people recommend? I'm presuming the ply will be 12mm so ideally I'd like them to be less than 18mm to avoid any pipework. Does this sound the way to go?

Good morning all. I'm sure this questions be answered before but used hardie a while back and found that when screwing there recommended screws into the board the heads of the screw sat slightly prob of the board and either didn't go down or was a nightmare to get in board level. I gave marmox a...

Hi there, this is my first post and just like to say hi and thank you for this very informative forum but just wanted to ask 2 questions. i will be tiling are upstairs bathroom, its a very small area only 2.5 m2. im going to lay hardibacker 6mm on top of the wooden floorboard...