Hi,
I have installed a shower former; the type that is a foam core sandwiched by a meshed cement layer either side:
The mosiacs that I wanted to install will be lower than the drain surround (even with the adhesive).
I have included some pictures below of the mosiac layed next to the...
Hi there,
I’ve just joined the forum so hello to all.
Im hoping some kind people can give me some well needed advice...
I’m remodelling our en-suite at home and I’m building a wet room. I bought a ready moulded former tray for the shower from here ...
I am retrofitting a 1200 X 760mm shower tray into an irregularly dimensioned shower room 1200mm X 1200mm X 1000mm X 780mm. The short sides are parallel and square to one long side. This leaves a roughly triangular area 1200mm long and about 30mm wide at one end and 240mm at the other which I...
Hi all,
I need to replace a shower tray. It sits on a base of plywood so I reckon it was glued. No access from underneath.
Any recommendations on how best to do this? Brut force? Chisel and hammer? Or is there a more advanced way of doing this?
The tiles sit on top of the tray - do I have to...
Hi all,
just after a quick bit of advice.
I am planning to install a shower tray onto a tiled plinth in similar way to the image attached.
i haven't bought the tiles yet but i am about to build the plinth.
Question:Should i avoid strips of tile less than a certain width on the top edge?
I don't...
I just bought a house and noticed the stone resin shower tray is leaking.
The Silicon job is pretty crap so I started removing it with the aim of redoing it properly but noticed the shower tray is still wrapped in plastic around the edges meaning the Silicon hasn't bonded to the side of the...
Hello people. Been up to the eyes with life, but finally managed to progress my (now 6m long!) wetroom project.
All tanked ready to go, but wondering which way you pro’s would set out this tray. 315 square tiles, and with one sitting dead centre on the tray, hard against the front edge of the...
Dropped a tile in a bath yesterday, I'm sure we've all been there.
Decided to try one of these repair kits from tool station before spending a small fortune on a bath repair man.
The results were much better than expected, well worth getting one to keep in the van..
Hello!
New to the forum and my first post on this after doing a bit of searching. I'd be interested to know your thoughts/experience of fitting BAL Board or Hardiebacker under the shower tray. The reason I ask is that with the build-up i'm looking at, if I installed the shower tray on the ply...
Hi all. I just dropped a tile onto a white plastic coated stone resin tray. I know, clumsy bugger. But im sure I'm not the first. Before i contact a repair company has anyone got any tips for repairing it? Its a dent about 5mm x 3mm and 3mm deep. I'd of thought colour matching would be the hard...
After some advice. I've scoured different sites looking for the right way and there seems to be so many different ways to do this.
I have a shower tray to install against stud walls with cement board fixed to it.
What is the right or best way to seal the tray in properly? I've seen videos...
All,
I am looking for some advice.
When I updated my bathroom eight or so years ago I used Hardie Backer boards on the wall all the way down to the floor. I then built a raised wooden structure and installed a stone resin shower tray on top. I filled the small gap where the tray met the hardie...
Planning to tank my en-suite tomorrow, using the BAL WP1 waterproofing kit. The ceiling is existing painted plasterboard. Do I need to tape and treat the joints between wall and ceiling like I do for the corners?
My gut says no, as the WP1 can't be painted on etc after. Presumably if I don't...
The wooden floor on upstairs en-suite is sound and level and i have planned to install a 800 x 900 stone resin shower tray. See attached photos of the floor. The instruction says to lay the tray on S/C mix.
Do i lay the sand/cement mix straight on the wooden floor or PVA before putting S/C?
To...
Hi there, we fitted a large Fiora shower tray into our upstairs bathroom a few years ago when we got the house refurbished. (pics attached) Problem is the weight of the tray has caused it sink into the wooden floor beneath, creating a 1mm gap between grout and tray and leaking a lot of water...
Hi, my mum would love a wetroom, but finding it difficult to fugure out some of the practicalities.
In houzz etc. we see wetrooms with few tile cuts which look glorious. Somehow the tiles must be angled to allow the water to drain away. But I'm unsure of how to find these trays online?
Should...
hi guys after some help
Am in the process of re doing ensuit. Have ripped out shower and base and want to know does the hardie backer go behind or on top of stone resin square tray? 3 walls are to be tiled and don’t think with the hardie backer installed all the way to the floor the tray will...
Hi,
We've just had a wetroom put in and everything has gone really well and I'm happy apart from the tiling around the drain. I assume this isn't the finish/ standard that I should be getting? Or does it just need to be grouted/siliconed?
Hi all
Have read many posts on this forum and it has been a great help. This is my first post though.
So I'm trying to install a new shower tray into a recess (walls on three sides). I don't understand how I can get the tray flush against all three because even if the walls are perfectly...