ufh

just a quicky ,just hought id ask what youve been using on ditra with ufh ,adhesive wise,cheers you nice tilers

Started today, 900x600 limestone job. Customer wants 8mm ish joints so that makes it a bit easier on the eye with the chiseled/tumbled edges. They are undecided on which grout colour, I was leaning towards a grey for these, would like some opinions please. Start laying tomorrow on top of the...

Hi all, some advice would be greatly appreciated. So the builder messed up in the loft during a major renovation in our house. In short, we have UFH boards laid out throughout the loft room and the en suite. At this point, the polypipe type foam boards and attached pipes are all on the same...

ok i went to look at a job wet ufh with flo screed on top all dried out etc the problem is in the dinning room they have laid a wooden floor and the tiles are to go around the primiter of the floor the into the kitchen through to the wetroom and basically they have lifted the former in the...

Hi guys and gals. This might be in the wrong forum area so I do apologise. It’s also my first post so please be gentle. I need some advice on advised installation steps for UFH. So I’m currently having a large dining, kitchen, living area renovated. We have an electrician install Prowarm...

All Please could you advise which is the best thin screed to go with for UFH? I know it will be a liquid of some sorts and I presume 40mm is minimum I can get away with? I will be tiling on top. Im trying to maximise the amount of insulation I can get underneath a Block and Beam floor with...

Hi, I am replacing a tiled floor and will need to overlay with 6mm backer board. This is on top of 15mm ply over wet UFH in dry screed. I need a backer board with the highest k-value (lowest R-value). So far from the data sheet 6mm hardiebacker has a k-value of 0.19W/mK. Does anyone know...

Does anybody how long s and c screed has to down before ufh can be commissioned or is it moisture dependent.

Hi, I am looking for an UFH screeder in sunderland that know what they are doing. Any recommendations? Will be Porcelanosa Acero tiles going down on top. Recommended tiler also welcome. 107m2 @ approx 65mm. Thanks.

Just checking. I’m having a warmup UFH wire laid and I’ve bought a Heatmiser NeoStat-e rather than a warmup thermostat. Will this be ok? Thanks

So I've narrowed it down to: Raychem T2, prowarm or Devi mats. All come with a Wi-Fi thermostat Devi and raychem seem slightly cheaper but I'm more interested with the quality. EBay seems to be the place to buy these mats, significantly cheaper than online retailers. The areas I'm looking at...

Hello everyone, we are in need of some sound advice on a dilemma we cant get 100% answers to, we are having a single storey extension and knocking out the back wall and dining room wall to form one large open kitchen/living area. We intend to fit wet UFH to the new part of the extension but we...

A new ufh screed is going to be laid in an extension. The existing flooring is a floating floor with plenty of 'bounce'. Customer would like both floors tiled. Old floor is approx 70m2 and the new screed is approx 30m2. Is it possible to do this as I don't think cost is an issue? Lewie

Hello all. I was hoping for some help with UFH issue. There seems to be many posts with similar issues but no answer fits all. I have had builders round to do a lot of work at my house. Part of it was digging out the floor and laying a wet UFH system. The room is approx 34sqM Damp proof...

Hi all, My name is Nic and I have signed up to the forum after reading quite a few very helpful threads over the last few weeks. My question is regarding a Wundafloor UFH system, which I know straight away is going to get a load of negative feedback but I have spoken to Mapei Technical...

All I have a house which has block and beam with 2 depths of space to play with for Water UFH. I have either a 55mm screed or a 85mm screed (house on 2 levels). I have dug holes so I can see what I have but not dug up all the screed yet. I also have timber suspended too but this I guess is far...

Hi guys, Any opinion on the best adhesive used with wet UFH for marble tiles? Also any advice on tiling over an existing porcelein floor with electric UFH - did want to rip it up and start fresh but the tiled surface is very solid, so felt tiling straight over would be good (and wouldn't have...

hi all I’m hoping for some technical advice on screeds and commissioning wet underfloor heating. I went to look at at 40m2 of floor tiling job yesterday the customers would like the floor tiled before the 22nd of next month as the kitchen is being fitted then. The wet underfloor heating system...

hi all, advice needed please, I have been asked to lay travertine in a kitchen on top of UFH. I went to look at the job today and the floor is concrete and has been pained twice. Do I need to try and remove the paint or can I key it before fixing insulation board etc? Also would you level the...

Hello fellas, New to this forum thought I'd get some opinions on my method as I've never dealt with tiling over gypsum liquid screed. I also have wet underfloor heating over 40m2. The screed was laid 4 weeks ago after 9 days I sanded the laitence off and primed with Weber. My plan is to use...