Electrical Advice

Speaker Cable for DoorBell Discussion ThreadSpeaker Cable for DoorBell Electrical Advice

Good evening Guys

Was wondering if someone can advise.

Ive wired a door bell system on a job in speaker cable( was last minute floors were going down and only thing in the van)

However when connecting up the kit as per instructions i cannot seem to get it to operate.

Is speaker cable suitable for doorbells

Thanks

Speaker Cable for DoorBell for the original thread on Electricians...

 

Replacing old 1970s two gang double light switch with new one, back to old wiring red and black, also has another switch which isolates both, Discussion ThreadReplacing old 1970s two gang double light switch with new one, back to old wiring red and black, also has another switch which isolates both, Electrical Advice

...

 

Extending ring Discussion ThreadExtending ring Electrical Advice

Hi guys, I’ve just been to a customers house. It’s an old house which has a few radial and ring circuits for sockets. They want 4 extra sockets to be installed. The ring circuit is feeding the whole house (not kitchen) would it be ok to tap into the ring circuit feeding the house and add the 4 extra sockets.

Thanks guys

Extending ring for the original thread on Electricians Forums

 

New extract fan, severe draft Discussion ThreadNew extract fan, severe draft Electrical Advice

Hello,
As many, I'm for expert advice. I just had an extract fan fitted in my kitchen. The make the electrician brought was Addvent, I think 6 inch fan. I realised today, sitting about 9 foot from the fan eating a meal that there was a very unpleasant cold breeze. The whole room is just not warm now but the wind caught my attention. As its been snowing & the wind is coming from the east it...

 

Heater running at 1600 watts Discussion ThreadHeater running at 1600 watts Electrical Advice

I recently purchased a space heater and before using it full time I plugged in my watt meter to see how many watts and amps it pulled. I was not happy to see 1600 watts at 13.1 amps which is above code I believe. Should I return it? It seems unsafe to run for 8 hours or so on high

Heater running at 1600 watts for the original thread on Electricians Forums

 

🤔?? Modra electric power..ac generator wiring diagram.. anybody have Discussion Thread🤔?? Modra electric power..ac generator wiring diagram.. anybody have Electrical Advice

Dose any one .?

🤔?? Modra electric power..ac generator wiring diagram.. anybody have for the original thread on Electricians Forums

 

Minor works - Zdb & R1R2 tests Discussion ThreadMinor works - Zdb & R1R2 tests Electrical Advice

Hi all, when completing a minor works there are two tests that i am unsure the best way to go about, example extension of circuit and new lighting point installed. Fed from industrial 3P board unable to isolate due to plant running. Do not wish to open live board even just for testing purposes for safety reasons. ( don't want to be putting hands in there with single insulated cables etc...

 

Completing electrical certificates Discussion ThreadCompleting electrical certificates Electrical Advice

Hi all, question on testing and completing certificates inside a large factory in maintenance, a lot of the 3P boards here are full of cables, when we are adding to existing circuits, it would be required to perform the necessary tests, R1 R2 and Zs for instance inside the boards, how do we go about this when we are unable to isolate the board, having to open up an old board...

 

Stovetop Discussion ThreadStovetop Electrical Advice

New stove top was recently installed. The next day I couldn’t get it to turn on, so I turned off and on the breaker. Went to the stove top and it worked perfectly making dinner.
The next day I can’t turn it on again, same thing, turn off and on the breaker and it’s working fine.
What’s wrong here?
Shouldn’t be a fault. Is it overloading after working fine for an hour or is there a reset switch that wasn’t connected in...

 

Stove top breaker Discussion ThreadStove top breaker Electrical Advice

New stove top was recently installed. The next day I couldn’t get it to turn on, so I turned off and on the breaker. Went to the stove top and it worked perfectly making dinner.
The next day I can’t turn it on again, same thing, turn off and on the breaker and it’s working fine.
What’s wrong here?

Stove top breaker for the original thread on Electricians Forums

 

Xmas lights Discussion ThreadXmas lights Electrical Advice

Bought a set recently from a Bedfordshire supplier, although a Chinese firm.
Couldn't believe the "mains" cable and the fitted fuse.
Mains cable is flat 3mm x 0.6mm. Fuse is 13A!!!
Plug is one of those Chinese specials with reduced dimensions.
See pic.

Xmas lights for the original thread on Electricians Forums

 

Proof of apprenticeship 1970s Discussion ThreadProof of apprenticeship 1970s Electrical Advice

A question to anyone who served their apprenticeship in the Uk during the 70s and early 80s,do you remember what paperwork you were given on successful completion of you apprenticeship,I hit my C&G certificates and I remember getting a paper sjib card but nothing else, the card was lost a long time ago, now trying to get a new grading card but without proof of my apprenticeship it is...

 

What is this sound from the electricity panel? Discussion ThreadWhat is this sound from the electricity panel? Electrical Advice

I ve heard this sound from electricity panel. What could it be?

What is this sound from the electricity panel? for the original thread on Electricians Forums

 

looking for work in Stevenage Discussion Threadlooking for work in Stevenage Electrical Advice

Hi, i am currently looking for a job, to turn in to a career.

I live in Stevenage, Hertfordshire I have car and can travel, looking at getting a van if staying self employed

currently hold level 2 2365 - 18th edition. Looking at doing 2391 soon along with part p and any other course i need to complete to become fully qualified, all self funded.

I have some hand tools with some power...

 

DIY - new oven tripping DB. Discussion ThreadDIY - new oven tripping DB. Electrical Advice

hello all,

btw I'm a plumber.... do I hear groans?! I installed a new Neff oven, DB is 0.5m away through a wall, wired into spare 16A MCB (house was built 2019) with 2.5mm T&E via 20A switched outlet, manufacturers lead with moulded plug (wired into outlet - not shortened).

... plug lead into oven... pop... both RCD's trip.
... switch outlet on... ditto
... switch MCB on... ditto

Neff...

 

Newbie Discussion ThreadNewbie Electrical Advice

Good evening Sparks,

Im Steven a trainee sparky. I passed my 2365 L2 and are currently working my way through L3 2365 and NVQ. Ive got a 2hr writtwn exam to take and ive yet to start the 615 design unit. Im doing all my training over at Thompson Training Ltd in Bury st Edmonds.

Newbie for the original thread on Electricians Forums

 

EasyMCS or Paperclip Discussion ThreadEasyMCS or Paperclip Electrical Advice

Sole trader looking to get my MCS accreditation for solar PV. I need to get a QMS in place for assessment and installations moving forward, I am looking at easymcs and paperclip to make the process as simple as possible. Which of these would be the most beneficial to my situation? Hoping people that have tread this path before have experience of both and can recommend.

Thanks

EasyMCS or Paperclip for...

 

Where to calibrate a MFT in Lomdon Discussion ThreadWhere to calibrate a MFT in Lomdon Electrical Advice

Where to calibrate (MFT) in London UK

Where to calibrate a MFT in Lomdon for the original thread on Electricians Forums

 

MF 32-40a joint Discussion ThreadMF 32-40a joint Electrical Advice

Hi all,

Just been on a kitchen remodel, has used the existing cooker feed due to difficulty of run/budget, but the kitchen fitter has kindly put a couple of rows of shelf brackets directly above the cooker switch and perfectly pinned the N to the CPC. Builders being builders seem to think it's fine as the fault "disappears" when the screw in question is removed.
I'm unhappy and will ultimately go and fix and make...

 

Help with light blowing breaker. Not newly fitted. Discussion ThreadHelp with light blowing breaker. Not newly fitted. Electrical Advice

dining room light suddenly started blowing the lighting breaker in the house.
I’ve had the boards up and can’t see any shorts in the wiring. It happens even when the light fixture is removed.

Flick switch, breaker blows.

Looking for what to try next to be honest.

Any help greatly appreciated.
Lee

Help with light blowing breaker. Not newly...